半径的

Virtual workspace and virtual maximum inscribed circle radius are proposed as indices to compare the abilities of orientation of these mechanisms.

分析了不同参数条件下3种可用于混联机床的并联机构：Stewart并联机构、动平台共用铰链机构以及中心伸缩杆机构，提出了虚拟工作空间和虚拟最大内接圆半径作为指标评价姿态实现能力

Taking the radius of disks as the intermediate variable, the process for analysis and synthesis of this kind of cavity is also given.

给出了用盘荷半径作为中间量进行腔体分析和综合的方法和步骤。

By taking the radius of disks as the intermediate variable, the process for the analysis and synthesis of this kind of cavity is also presented.

给出了用盘荷半径作为中间量进行腔体分析和综合的方法和步骤。

There is only one set of exciting coil, and the isochronous magnet field is mainly determined by the shape of magnet pole.

它沿半径方向只用一套线圈励磁，等时性磁场的建立完全由磁极形状决定。

The curvature radius was derivated and the contact stress of the three-arc-sect isometric type surface was calculated through the elastic dynamics theory.

应用弹性力学理论，推导出接触点的曲率半径，对三弧段等距型面联接进行接触应力计算。

The knifepoint geometry and cutting edge's blunt round radius are considered as critical parameters to get high quality for the machined surface.

认为正确地选择刀尖部分几何形状和修光刃钝圆半径是获得高质量加工表面的有力保证。

During the inversion of the dual lateral log, The generalized inversion method is used to invert the three parameter (the radius of the invasion zone, the resistivity of the invasion zone, the resistivity of the destination formation) and eliminate the affect of invasion zone.

对于双侧向测井反演，本文将广义逆反演方法用于消除侵入影响的三参数(侵入半径、侵入带电阻率、原状地层电阻率)反演中。

This paper discusses the least squares estimator circledetection method which is based on statistical theory. It gets the position through edge tracing and uses the edge point to estimate the center and radius of circle.

本文采用基于统计原理的最小二乘圆检测法，以边缘跟踪确定圆边缘点位置，以最小二乘法估计圆心和半径，精度可达亚像素级。

The path density of relative movement is derivative of path arc length s to lapping tool radius R i.e.

相对运动轨迹密度就是相对运动轨迹弧长 s 对磨具半径 R 的导数，即 ds/dR 。

The design of the 3-dimensional trajectory in horizontal wells is an optimal control system where the state variables are azimuth, inclination and the control variables are radius, tool-face angle and length of curve.

水平井三维轨道设计是以方位角、井斜角为状态变量，以曲线半径、装置角、曲线段长为控制变量，以入靶精度等为性能指标的非线性多阶段最优控制系统。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。