半径的

The article analyzes the dominant factor of gas well productivity based on absolute open flow potent and binomial deliverability equation.

结合气井绝对无阻流量定义及气井的二项式产能方程，对影响气井产能的井底污染、地层渗透率、地层压力、地层有效厚度、气井半径、泄气半径、天然气粘度、硫的沉积、气层产水等因素作了详细的分析。

Test and analysis show that, the distribution patterns of the tangent veloctiy fields in the big cone area and the small cone area, which are comprised of para-free vortex and para-forced vortex, are basically identical without a change of the radius of the boundary surface; with the increase of the angle of the small cone, the para-free vortex area decreases and the para-forced vortex area increases, and the emulsifiability of the fluid drips increases with the increase of velocity gradient; the tangent velocity increases with the increase of inlet flow, and the maximum tangent velocities of both the big cone area and the small cone area are 4.94 times of the inlet flow; and the maximum tangent velocity increases with the increase of the split ratio and with the radius of the boundary surface not changed.

试验分析表明，大锥段和小锥段切向速度分布规律基本相同，均由准自由涡和准强制涡构成，分界面半径rm没有变化；随着小锥角θ的增加，准自由涡区缩小，准强制涡区扩大，速度梯度增加会加大液滴的乳化程度；随入口流量增加，切向速度增大，经拟合得出大锥段和小锥段的最大切向速度均为入口流量的4.94倍；分流比加大，分界面半径基本不变，最大切向速度增加。

Four circles of radius 1 are each tangent to two sides of a square and externally tangent to a circle of radius 2, as shown. What is the area of the square?

A 32 22+12 2 16+16 3 48 36+16 2 中文：如图所示，四个半径是 1 的圆分别与正方形的两边相切且与一个半径是 2 的圆外切，这个正方形的面积是多少？

The influence of indentor radius on the plastic deformation has been discussed and some important results are as follows:(1) The influence of the ratio of ceramic coating thickness to indentor radius on the failure of coating, plastic deformation of substrate and crack propagation are obvious.(2)The propagation of crack in ceramic coating is assumes to be of semi-elliptical shape under normal contact with a rigid sphere.(3)Fatigue life of ceramic coating is mainly decided by substrate and load, the lower substrate elastic moduli and load, the more cycles of fatigue.

分析了压头半径对塑性变形的影响，模拟结果表明；(1)陶瓷涂层厚度和压头半径之比对涂层失效、基体塑性变形及裂纹的形成有显著影响；(2)在刚性球压头静态挤压条件下，陶瓷涂层中的预制裂纹按照椭圆形裂纹规律扩展；(3)陶瓷涂层的疲劳寿命与基体和载荷有很大关系，基体弹性模量越小，疲劳寿命延长。

In the solution of the Difichlet boundary problem ofLaplace equations, we provide an effective method for determining the spectral radiusand the best slack variable of block basic iterative methods. At the same time, wepresent the spectral radius and the best slack variable of basic iterative methods from thenine-point difference scheme.

在解决Laplace方程Dirichlet边值问题上，文章为确定块基本迭代方法的谱半径和SOR方法最优松弛因子提供了一个有效的方法，并推导了九点差分格式下的块基本迭代方法的谱半径和SOR方法最优松弛因子。

Finally, for the spectral radius of a graph with a cut vertex, we give an inequality concerning the spectral radius of the graph and its subgraphs.

最后，对于有割点的图的谱半径给出一个与子图的谱半径有关的一个不等式。

The experiments and simulations are performed by using a conical lens whose radius is 15 mm and basic angle is 1°. The experimental results are compared with the theoretical analysis and computer simulation results. The comparison indicates that the influence of eccentricity on the diffraction mode decreases as the radius of curvature of incidental spherical wave and the propagation distance decrease.

使用半径为15mm，底角为1°的圆锥透镜进行计算机仿真和实验，最后将实验结果与理论分析和仿真结果相比较，证明球面波的曲率半径和出射光束的传输距离越小，偏轴对衍射模式的影响越小。

It is proved that the obtained radial and tangential stress curve link glossily at hardening zone radius r=R, and softening zone radius r=R and curve of tangential stress σ(subscript θ)/p0-r/α has not up-pinnacled stress concentration especially, the result goes all the way with the experiment result of Japanese scholar Jiuwubosheng.

证明了所求得的巷道围岩径向和切向应力曲线在硬化区半径r=R和软化区半径r=R处均光滑连接，特别是所求得的切向应力σ/p0-r/α曲线没有尖峰向上的应力集中，此结果与日本学者久武胜保的试验结果一致。

Diopter, corneal curvature, depth of anterior chamber and the axial length of the eyes were measured. We calculated the concordance of hyperopia, intrapair correlation coefficient and heritability index of monozygous and dizygous twins.

调查了同卵和异卵双生子的屈光度、角膜曲率半径、前房深度、眼轴长度，计算了远视的一致率，同卵和异卵双生子的组内相关系数及遗传指数等项目，证实远视眼是一种多因子遗传病，它的发生除了与多个遗传性状如角膜曲率半径、前房深度、眼轴长度等有关外，还与环境因素有关。

To meet the demand of higher built-up rate ,single-bending screw drill tool with large angle is used during the drilling of the moderate-and short-radius horizontal well.

钻中短半径水平井，在采用弯角较大的单弯螺杆钻具以满足高造斜率的需要时，由于套管内径较小，螺杆钻具钻头处位移比较大，螺杆钻具能否顺利通过直井段是钻中短半径水平井面临的一个重要问题。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。