半径

The critical heating rate for different body radius was predicted by comparing the gas pressure when the peak degradation rate occurred with the threshold body strength which was determined by the diametric compression test of the green body during thermal debindering.

摘 要：以聚乙烯醇和NiFe2O4/Ni型金属陶瓷压坯为对象，采用热重分析研究PVA在N2气氛中的热脱脂行为，建立PVA热脱脂速率的数学模型，在此基础上，模拟并计算PVA分解产物气体在多孔粉末压坯内的压力构建情况；结合粉末压坯脱脂强度测试结果，分析粉末压坯在脱脂过程中压坯尺寸、粘结剂含量等因素对升温速率和脱脂时间的影响，获得不同半径尺寸压坯的极限升温速率。

For comparison, damage radius for microsurgical scissors was 50 μm, and for diathermy, 400 to 850 μm.

与之相对比的是，微手术剪产生的破环半径是50 μm，透热疗法则是400 to 850 μm。

We find that thecontribution to differential cross section related to electron is farlarger than that related to hole, and it varies with differentsemiconductor materials, cylindrical radii and energies of incidentphotos.

结果发现：在自由和受限柱形量子线中，电子对微分截面的贡献要远大于空穴，且贡献随半导体材料、柱形几何半径及入射光能量的变化而不同。

In this paper, the theoretical model of CQI is described in an atom-diatom system in the condition of the molecular beam, based on the first-Born approximation of time dependent perturbation theory, taking into accounts the anisotropic Lennard-Jones interaction potentials. The method of observing and measuring correctly the differential interference angle is presented. The relation between differential and parameter, velocity is obtained. The relation of the integral interference angle and temperature is discussed.

文中利用一阶含时波恩近似和L-J相互作用势，建立了原子-双原子分子碰撞系统转动传能的量子干涉模型，描述了观察和测量微分干涉角的方法，得到了微分干涉角与碰撞半径和碰撞速度间的关系，同时也得到了积分干涉角和实验温度的关系。

We want to lower the aggro range and spawn the ghoul in quicker when dismounting.

食尸鬼的引怪半径会被缩小，同时在你下马的时候它们会更快的钻出来。

The radius of a circle is the distance from the centre to the edge.

圆的半径是圆心到圆周的距离。

Many of them, the higher-ranking individuals for the most part, left altogether, and the others settled down at a safe distance, forming a rough circle about eighty yards around the lions.

很多鬣狗，尤其是绝大部分的地位较高的鬣狗一起离开了，而其他的鬣狗在一个安全的距离上呆着，以狮群为圆心形成了一个大约80码半径的不规则圆圈。

A method of determination of the base circle and offset distance was presented and a designer can ascertain the principal size parameters of disk cams correctly or take them as the original numerical values for design.

主要分析了偏置式推杆盘形凸轮机构的主要尺度参数与所给定运动参数之间的关系，并提出了基圆半径r0 ，偏距e等的取值原则与方法，从而准确无误地确定凸轮的主要参数，或是把此参数作为设计变量的初值。

The method for the point sets selection of point Hough transform and the scan direction for image of searching the point sets were improved by using the geometrical characteristic of the concentric circles:The center of the concentric circles was obtained in the accumulative array firstly,radius was obtained by the mean of distance between the circle center and every edge points afterwards,both the circle center and the edge of the concentric circles were detected accordingly.

利用同心圆的几何特点对点Hough变换边缘点的点组选取方法和搜索点组的图像扫描方向进行了改进：首先由累加阵列确定同心圆的圆心，然后由圆心到各个有效边缘点距离的均值求出半径，从而检测出同心圆的圆心与边缘。

Stub Pitch is a number used to denote the radial distance from the pitch circle to the major circle of the external spline and from the pitch circle to the minor circleof the internal spline.

残余径节：残余径节是一个数，它用于表示节圆与外花键的大圆或内花键的小圆之间的半径差。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。