半径

Input (0,0) to determine the center of a circle position, and then enter a radius value "8", draw a circle

2输入（0，0）以确定圆心位置，再输入半径值"8"，画出一个圆

Our next goal is Shanghai two hours -- with Shanghai as the economic circle center of a circle, the radius of the region for two hours.

我们下一步的目标就是上海2小时经济圈――以上海为圆心，2小时车程为半径的区域。

Expanding from the center of the circle get a maximum boundary in the limitation of 80㎡get a circle with radius 5m.

从这个圆的中心扩张，在80平米的限制之下得到一个最大化的边界：半径为5米的圆。

A line segment that joins the center of a circle with any point on its circumference.

圆半径：将圆心与圆周上任一连接起来的线段

Continue to use the above command to make a round, enter the center of a circle points (-40,-30), respectively, enter the radius value of 8 and 16, draw another set of concentric circles.

4继续用如上的命令作圆，输入圆心点（－40，－30），分别输入半径值8和16，画出另一组同心圆。

What this text to study is according to an detection by the transformation of HOUGH, some round characteristics value will bi found, like the round radius and the center of a circle.

本文所要研究的是基于HOUGH变换的圆检测，即通过HOUGH变换提取出被检测圆的一些特征值，如圆的半径及圆心所在的坐标。

The combined motion of grinding the transition arc maintains that the gyration center of the arc moves along the parallel line to the surface of the grinding wheel, and the gyration center of the oxide tool moves along the vertical line to the surface of the grinding wheel.

磨削刀片过渡圆弧时，过渡圆弧的回转中心到砂轮面的距离必须恒等于过渡圆弧的半径，磨削过渡圆弧的复合运动要保持过渡圆弧的回转中心沿平行于砂轮面的直线运动；刀片的回转中心沿垂直于砂轮面的直线运动。

4A series of factor such as the difference about the centre of figure and the shear centre, curvature radius, central angle is discussed.

4对曲线梁中的剪、形心位置的差异以及曲率半径、圆心角、预应力大小、摩阻损失等内力影响因素进行了分析。

We use the waveguide simulation software BeamPROP? to analyze the effects of the Y-branch angle, the radius and central angle of arc waveguides, and the length of straight waveguide on insertion loss and nonuniformity.

采用光波导数值模拟软件BeamPROP~分析Y分叉角度、圆弧波导的半径与圆心角、直波导长度等结构参数对插入损耗与分光均匀度的影响。

Any circular node is defined by its central point and radius.

任何通告节点的定义是其核心点和半径。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。