半径

Analysis and research were made for relation about max external pressure resisting capacity under condition of different ratio between straight section length and end arc radius on the flatted tubes with same circumference and tube wall thickness by using analytical technology of finite element.

应用有限元分析方法，对相同周长、相同壁厚的扁管在直边段和圆弧半径的不同比值条件下与所能承受最大外压力的关系进行了分析。并对计算分析取得的数据进行拟和得到了扁管在直边段和圆弧半径的不同比值条件下能承受最大外压力的关系及经验公式

In order to search thelargest possible area, the maximum range for this aircraft was selected (24 hexes).

为了尽可能搜索更大的范围，此处将执行半径设置到它的最大半径(24格)。

The magnetomechanical modeling of spherical magnet incased in spherical vessel is established. The influence to magnetic force by magnetic conductivity, remnant magnetism and radius of magnet, radius of container and off-centering of magnet is analyzed. The conclusion has universal character.

以球形永磁体和球形容器为对象，推导出永磁体磁浮力模型，分析磁导率、永磁体的剩余磁化强度和永磁体半径、容器半径以及永磁体相对于容器中心位置的位移对磁场力的影响，结论具有一定普遍性。

Utilizing the extremum theory of function to obtain the minimum radius of curvature of theoretical profile, and factors that affecting the minimum radius of curvature were discussed, thus provided theoretical basis for the studies of the continuous contact transmission of swinging movable teethed central gear meshing pair, contact stress and meshing stiffness etc..

利用函数极值理论得到理论廓线的最小曲率半径，讨论了最小曲率半径的影响因素。为摆动活齿中心轮啮合副的连续接触传动、接触应力和啮合刚度等的研究提供了理论基础。

The curvature radius and vehicle speed effects were analyzed based on the dynamic amplification factor of a curved-bridge considering the traveling eccentricity of vehicles.

内力和位移的动力放大系数对曲率半径的变化的敏感性各不相同，当曲率半径小于某个特征值后，动力放大系数变化很大。

Therefore, the face-width of the face gear is limited. According to the conditions of undercutting and pointing, the formulae of minimum inner diameter and maximum outer diameter are derived for the shaft angle face gear .

根据产生根切与齿顶变尖的条件，给出了任意轴交角下齿宽设计的公式，定义了两个无量纲参数，即最小内半径系数和最大外半径系数，来表示齿宽的设计范围。

Based on the simulation data, the effects of clearances, damping coefficient and the rotation speed on the dynamic behaviors are studied: compared with ideal mechanisms, mechanisms with clearances are less stable; as for mechanisms with clearances, when the crank rotates at the speed of 100rad/s, the actual clearances are always above the radium of clearances, axle pin and axle cover keep contact throught the rotation; when the crank rotates at the speed of 20rad/s, mechanisms are in an unstable state, at an angle of about 300, the actual clearances are below the radium of clearances, pairs lose contact, which results in collision between them; with the speed of 20rad/s, when damping coefficient is assumed 175Ns/m, distinct separation and collision happen between pairs; when damping coefficient is assumed 220Ns/m, separation and collision are controlled.

在含间隙机构中，当曲柄以100rad/s转动时，运动副间隙始终大於半径间隙，轴销与轴套始终保持连续接触；当曲柄以低速20rad/s转动时，系统处於极不稳定的震荡状态，在转至300°左右时，运动副间隙小於半径间隙，脱离接触，发生明显的分离碰撞现象。在含间隙机构中，曲柄以低速20rad/s转动，当取法向阻尼系数为175Ns/m时，副元素发生明显的分离碰撞现象；当取法向阻尼系数为220Ns/m时控制了副元素的分离，副元素一直处於连续接触状态。

The cobalt blue bulb glass manufactuerd by soda-lime silicate is substituted for different proportion of potassium, sodium and lithium.

透过这些钴蓝玻璃的灯泡发光钨丝呈现不同的颜色，含大离子半径碱的呈红黄混合色，含小离子半径碱的呈纯正红色。

Quite a large radii to fold, forming using the coining method in a brake press was not acceptable due to the fact that the finished radii would have an appearance similar to a twenty pence piece!

相当大的半径折叠，形成使用铸币方法在制动新闻是不能接受的原因是，成品半径将有出现类似21便士一块！

This paper takes account of the several factors including the contour curve of cam,the accuracy of motion, structure size and the time of normal work of cam mechanism by discussing the relationship between the roller radius and contour curve ,the touch-stress between the roller and cam, the thickness of lubricant film.

以凸轮机构的凸轮轮廓曲线、运动的准确性以及结构尺寸和寿命为考虑因素，讨论了凸轮机构从动件滚子的半径与轮廓曲线、凸轮高副的接触应力以及润滑油膜厚度等的关系，提出了滚子半径的选择原则。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。