升温的

As many enthusiasts pining for the second and third-generation Focii that arrived in Europe (and even Mexico, for crying out loud) well know, the United States and Canada continue to receive a mildly warmed-over version of that 2000 Focus.

正如许多爱好者渴望的第二和第三代Focii抵达欧洲众所周知，美国和加拿大继续得到温和升温，超过版的2000年焦点。

A set of laser monitoring observation system to be used for measure the solubility with a high speed, which is programmed heating apparatus , have designed. The solubility of 1,2-cyclohexanediol were measured in water, methyl acetate, acetic ester, propyl acetate, butyl acetate, methyl acrylate, ethyl acrylate, acetoacetic ester at different temperature.

另外，还建立了一套带激光监视系统，可以控制升温速率的溶解度测定实验装置，测定了反式-1，2-环己二醇在水、乙酸甲酯、乙酸乙酯、乙酸丙酯、乙酸丁酯、乙酰乙酸乙酯、丙烯酸甲酯、丙烯酸乙酯和甲基丙基酮等9个二元体系中的溶解度。

The heating curing and isothermal curing processes of polyacrylate were studied by Torsion Barid Analysis.

利用动态力学扭辫分析研究了聚丙烯酸酯的升温和恒温固化过程，提出了一种两步固化机理，并求算得到了体系的固化活化能，发现有机锡催化剂能有效降低固化活化能并讨论了其催化历程。

An acrylic resin was synthesized by the radical copolymerization with methyl methacrylate, butyl acrylate and methacrylic acid monomers in solution using benzoperoxide as initiator. Appropriate parameters of monomer ratio, monomer concentration, solvent, and reaction temperature were found by experiment.

以过氧化二苯甲酰为引发剂，采用溶液聚合合成了甲基丙烯酸甲酯-丙烯酸丁酯-甲基丙烯酸树脂，通过实验确定了自由基共聚合适宜的单体配比、单体浓度、引发剂浓度、溶剂以及反应的升温速度。

The catalytic activity and selectivity for hydrodesulfurization and hydrodenitrogenation were studied by using benzothiophene, dibenzothiophene and quinoline as model compounds.

在N2-H2下，利用程序升温还原氮化反应制备氧化铝负载的β-Mo2N0.78催化剂，并以苯并噻吩、二苯并噻吩和喹啉为模型化合物，考察该催化剂的加氢脱硫、加氢脱氮活性和选择性。

The factors include the calefactive process of stabilization,the temperature of carbonization and the condition of activation craft.

通过红外光谱和DTA/TGA分析对ACF的结构变化进行了探讨，并考察了稳定化升温程序、碳化温度及活化工艺条件等对ACF吸附性能的影响。

The effect of temperature descending rate, treatment temperature and calefactive rate on the relative wear resistance of GCr15 was investigated.

自行设计制造了能实现工艺参数自动控制的深冷处理系统，研究了深冷处理工艺过程中降温速率、深冷处理温度以及升温速率等工艺参数对GCr15钢相对耐磨性的影响规律。

The optimum conditions for preparing TiO_2 are as follows, pH value=1, n(C_2H_5OH)/n(TiBuO_4)=15, n(H_2O)/n(TiBuO_4)=3, calefactive speed 10℃/min, sinter temperature 450℃.

3制备高光催化活性的TiO_2的最佳工艺条件为：pH=1，n(C_2H_5OH)／n(TiBuO_4)=15，n(H_2O)／n(TiBuO_4)=3，升温速率10℃／min，烧结温度为450℃。

This thesis adopts the method of Sol-Gel to develop ZnO and ZnMgO alloying film and introduces the influence of technology parameters such as calefactive velocity, film thickness, anneal temperature on the performances of the film such as crystalline quality and photoluminescence in a detailed way.

本论文采用溶胶一凝胶工艺制备ZnO及ZnMgO合金薄膜，详细研究了升温速率、薄膜厚度、退火温度等工艺参数对薄膜的结晶质量和发光性能的影响。

And the parameters of SPS in this paper are: the synthesized temperature=900~1000 ℃, calefactive time=15min, calefactive rate in first 5 minutes=100℃/min, keeping temperature time=30min, pressure=40MPa.

本试验条件下，制备Ti-HA生物复合材料的最佳工艺参数是：温度在900～1000℃，升温时间15min且开始5min保持每分钟100℃的速率，保温时间30min，烧结加压40MPa。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。