加热的

The HEW series reaction heating device that the company produces prones to the leading level in the same trade,have,heat with high efficiency,low protecting advantaging such as being reliable fault rate.

公司生产的HEW系列感应加热设备在同行业中趋于领先水平，具有加热效率高、故障率低、保护可靠等有点，以优质的产品、满意的服务，为用户创造最大的价值。

The research and appliance of twofold combustion control system assure heating billets with high quality and little consumption, and provide a convenience for research heating techniques.

通过两级自动化系统的研发和应用保证加热出高质、低耗的板坯，并为加热工艺的研究提供研究的平台。

In this paper,an analysis of the temperature-rising processes of polyurethane foam placed in oxygenated and deoxygenated atmosphere respectively but under the same heat flux was made.

分析对比了相同加热条件下的聚氨酯泡沫材料在有氧和无氧气氛下的升温过程，并对不同加热条件下的聚氨酯泡沫材料的阴燃传播速度进行研究。

In this paper, an analysis of the temperature-rising processes of polyurethane foam placed in oxygenated and deoxygenated atmosphere respectively but under the same heat flux was made. And give a close study of the smoldering velocities of polyurethane foam under different heat fluxes.

分析对比了相同加热条件下的聚氨酯泡沫材料在有氧和无氧气氨下的升温过程，并对不同加热条件下的聚氨酯泡沫材料的阴燃传播速度进行研究。

As an example,the influence of hot zone on the thickness uniformity of ZnO thin films deposited by nebulized pyrolisys CVD was studied in this paper.

本文利用计算机程序简单模拟了圆盘状加热器和圆筒状加热器的热场分布，研究了热场对雾化裂解CVD法生长的半导体薄膜厚度均匀性的影响，并采用雾化裂解CVD技术制备了高度c轴取向的ZnO薄膜。

The results showed that when retrogressed by electrical current heating at 200 ℃ the tensile strength in re-aged 7A04 alloy extrusion bar of 60 mm in diameter reached 620-640 MPa and a uniform elongation appeared from central part to surface layer of the sample while the fracture time in test of resistance to stress corrosion under a load stress of 375MPa in 3%NaCl+0.5%H2O2 corrosion solution was greater than 30 d.

结果表明，直径60 mm的7A04铝合金棒材在200℃电流直接加热回归后再时效，从心部到表层的拉伸强度为620-640 MPa，延伸率均匀一致；在3%NaCl+0.5%H2O2水溶液介质中和375 MPa应力下的应力腐蚀断裂时间大于30d，而辐射式加热回归的为575 MPa，延伸率从心部至表层表现极不均匀，应力腐蚀断裂时间只有19 d。

The results showed that when retrogressed by electrical current heating at 200℃the tensile strength in re-aged 7A04 alloy extrusion bar of 60 mm in diameter reached 620- 640 MPa and a uniform elongation appeared from central part to surface layer of the sample while the fracture time in test of resistance to stress corrosion under a load stress of 375MPa in 3%NaCl+0.5%H_2O_2 corrosion sol...

结果表明，直径60 mm的7A04铝合金棒材在200℃电流直接加热回归后再时效，从心部到表层的拉伸强度为620-640 MPa，延伸率均匀一致；在3%NaCl+0.5%H_2O_2水溶液介质中和375 MPa应力下的应力腐蚀断裂时间大于30 d，而辐射式加热回归的为575 MPa，延伸率从心部至表层表现极不均匀，应力腐蚀断裂时间只有19 d。

Drying and heating the hanging goods,the products after thethrough the hot-air drying temperature,to spped up the process ofcuring the products,so that the Rubberizing product cementation can be more solid andfirmly.With a hanging and closing operation and three-dimensional-baking

为佛吉亚内饰公司生产的用于对产品进行悬挂式加热烘干的设备，可将粘接生产完成后的产品悬挂于加热烘烤专用挂钩上，通过一恒温热风烘干，加速产品的固化过程，使涂胶产品粘接更为牢固结实。

According to the theory of swaging process, robot...

本文根据已有的旋锻加工理论、机器人理论以及机械理论，认真地研究了旋锻加工过程及其自动化过程的实现型式，提出了利用气动机械手来代替人手进行旋锻加工的实施方案，方案包括：上料、加热、旋锻、调头、再加热、旋锻、移出等工序的自动化系统，并依此设计机械手主体、顶杆机构、换向机构、移送机构等子系统及其控制部分，并通过静力学、动力学分析以及三维建模仿真优化技术论证了方案可行性、可靠性，试图解决钨杆旋锻加工过程的自动化问题。

This furnace is supported for each kind of material drying equipment as a kind of general hot air unit, which is widely used for dehumidification of cereal, seed, feed and fruit, heating and wet extraction of vegetables, mushroom, jew's-ear, tea, tobacco, food, pharmaceutical products, chemical raw materials and light and weight industrial products, as well as for heating of various facilities and dehumidification of warehouses.

该炉为通用性热风装置，与各种物料的干燥设备配套使用。广泛用于粮食、种子、饲料、果品脱水、蔬菜、香菇、木耳、银耳、茶叶、烟叶等产品、食品、医药品、化工原料、轻重工业的产品的加热除湿，还可用于各种设施的加热以及库房除湿等。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。