加热的

The programmed calcination process is necessary, that is, heating the as-elutedhmmersed oxalates mildly from room temperature to 300℃at a heating rate of 5℃/min, and keeping the samples at 300 C for 1 h; consecutively, heating to 900℃at 10℃/min, and then keeping for 4 h.

程控的烧结过程是必须的，这就是，按5度/分钟逐步加热按这种淋洗制备的草酸盐到300度，保温1小时；接着，按10度/分钟加热到900度，保温4小时。

The water inside a horizontal vessel is heated by fired burner through burning channel, and the natural gas or crude oil in tube bundle or high pressure coil are heated by hot water.

燃烧器燃烧后通过燃烧道加热水平容器内部的水，然后利用放置在水中的高压盘管或管束加热其中的天然气或原油。

In the parameterized design of the hot wind furnace, the number of rows and columns of pipe bundle were always varied with design parameters, it was difficult to generate 3D parametric model of hot wind furnace.

在间接加热式热风炉的参数化设计中，蛇型管束的行数和列数随着设计参数的变化而变化，使得间接加热式热风炉三维参数化建模比较困难。

While the volumetric flask is heating and degraded directly,the content of total phosphorus in the circular water containing buffer erosion scale preventive agent of organic phosphorus can be determined.

含有机磷缓蚀阻垢剂的验收以及循环水中对总磷含量的测定方法，都要经过加硫酸和过硫酸铵加热氧化分解的过程，一般的标准方法都是采用在锥形瓶中加热，分解完毕再移入容量瓶中，进行显色测定。

In this paper,taking the rotary furnace of Tianjin steel tube company for the research object, an optimal mathematical model of the company's rotary furnace for continuing heating up semi-finished steel tube has been set up and the numerical analysis is made and a computer simulating interface has been developed .

以天津钢管公司的环形加热炉为研究对象，建立了环形加热炉管坯连续加热过程数学模型，并进行了数值解析。同时开发了计算机仿真界面，对管坯在炉内的加热情况进行了数值模拟，利用现场实验数据对所建立的数学模型进行了验证。

The most favorite parameters for processing Yuxiangrousi are that the thickness of material is 5mm, the pressure of sublimation is 140Pa, the pressure of desorption is 30Pa, the temperature of heating board is 20℃ by orthogonal experiments.

通过正交试验得出真空冷冻干燥鱼香肉丝的最佳工艺：鱼香肉丝厚度5mm、升华干燥时真空度140Pa、解析干燥时真空度30Pa、解析时加热板温度20℃，影响工艺的主要因素次序为加热板温度、厚度、升华压力和解析压力；以及复水量在原含水量Aw的140%～150%、复水温度65～85℃、复水时间20～30min最好；最后建立数学模型验证干燥时间。

The process calculation of the shell and tube steam heater was carried out with the method of numerical analysis method.

将数值分析方法应用于管壳式蒸汽加热器的工艺计算，很好地解决了试凑法的盲目性和计算工作繁重的问题，并在此基础上用VisualBasic语言开发了管壳式蒸汽加热器工艺CAD软件。

Based on this, combining with q-γ-τ matrix equation, the paper constructs matrix analysis models for calculating thermal economic and conversion factor of three typical auxiliary steam-water namely: in-out system from steam side of heater, water...

在此基础上，结合 q-γ-τ矩阵方程，针对三类典型辅助汽水(从加热器汽侧进、出系统、从加热器水侧进、出系统和纯热量进、出系统)，构造了相应的热经济性局部分析模型和转换系数λ的计算模型，具有通用性较强，宜于程序化的特点。

At room temperature thermoplastic plastic usually granular, after heated to a certain temperature molten state, while its cooling after Curing, if it will become once again heating molten state, and the plastics can be re-forming.

热塑性塑料在常温下通常为颗粒状，加热到一定温度后变成熔融的状态，将其冷却后则固化成型，若再次加热则又会变成熔融的状态，而可进行再次的塑化成型。

Thermoplastic plastic usually get granular at normal temperature , after heated to a certain temperature molten state, while its cooling after Curing, if it will become once again heating molten state, and the plastics can be re-forming.

热塑性塑料在常温下通常为颗粒状，加热到一定温度后变成熔融的状态，将其冷却后则固化成型，若再次加热则又会变成熔融的状态，而可进行再次的塑化成型。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。