加热的

The solder removing device comprises the restoring chamber(37) used to store the liquid heating medium whose temperature is above the solder's melting point, the substrate conveying machine used to convey the defectively soldered substrate in and out the solder treating pond, and the brush(45) used to rub the surface of the defectively soldered substrate immerged in the heating medium in the solder treating pond and rub off the solders which are over heated by the heating medium.

焊料移除设备(31)包括用于存储温度高于焊料的熔点的液体形式的加热介质的修复腔室(37)、用于输送有缺陷地焊接的基片进出焊料处理池的基片运输机、和用于摩擦浸入焊料处理池内的加热介质的有缺陷地焊接的基片的表面由此擦去通过加热介质过度加热的焊料的刷子(45)。

Objective:To heat by magnetic hotplate replaces heating rod in acid-fast staining.

目的：评价用电磁炉加热替代抗酸染色中的加热棒加热的可行性。

It is not usuallyfall below 18°C, a steam coil or electric immersion heater should be fittedto the tank. The solution deteriorates rapidly if heated above 35°C and athermostat MUST be fitted to a heated tank. Overheating the Alocrom

通常不需要加热浴缸，但是如果工厂的温度下降到18°以下，浴缸应该安装蒸气旋管或浸没式电热器，如果加热到35°以上，溶液会很快变质，因此加热的浴缸要安装上恒温调节器。

This paper introduces simply the development and application of induction heating technology, and the basic knowledge of induction heating.

本文以固态高频感应加热电源为研究对象，概略介绍了感应加热的基本理论及感应加热技术的发展和应用。

This is found to result from the existence of negative orography in this low-resolution model. It is shown that, over the grid-points where orography height is negative, there exists false sensible heat source that leads to warmer temperature and higher geopotential height.

利用位涡的特性，研究并模拟了大气流场在短时间尺度上对非绝热加热的响应，并提出了"过流"的概念：在加热层顶，即使非绝热加热消失，仍存在上升运动，反气旋涡度环流和冷中心。

The air in the fermentation room deflated to the inner plafond by the air blower and use radiator to heat, and blow the air into air deflector again. Repeat this process again and again until to achieve the required temperature.

通过风机将醒发房内醒发空间的空气抽到夹层天花内，然后经过散热器将空气加热，再将加热的空气吹到导风槽，通过导风槽出风口将热风送到醒发空间，这样不断循环加热，使温度达到所需要的醒发温度。

The results also show that resonance tube heating effects are related to the pressure oscillations in the tubes, whereas the pressure oscillations are related to the pressure of the driving gas, and further, different types of resonance tubes have significantly different heating properties.

实验结果确认了谐振管加热的主要机理是激波振荡累积加热机制，而且表明谐振温升与管内气体压力振荡幅值有关，而谐振管压力振荡幅值与驱动气体压力有关；结构形式不同的谐振管，加热特性显著不同。

Its work principle is that used steam or electric heating air,then made a cycling dry with heated air.

该机工作原理是利用蒸气或电加热器加热空气，然后由加热的空气对物料进行循环干燥。

The postvaccinal apple juice was treated by different temperatures,voltages,heating times,pH values and volumes.

分析了欧姆加热的温度、电压、加热时间、pH值及加热体积等对杀菌效果的影响。

Fill the piping with stuff, line to define the length and position for heating tube, daub tube, warm-up, make the role touch the piping by pressing the push-bike, heat up the piping to the necessary temperature, cut off power supply, one-off complete the process in the bending model.

在管坯内装填填充物、划线确定管坯加热的长度和位置、涂抹润滑剂、管坯装卡、预热、通过脚踏机构加压使电极与管坯紧密接触、采用二次加热工艺将管坯加热至所需温度、切断电源，在弯曲成形模具上一次性完成管坯的弯曲成形加工。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。