加热元件

In the light of cost index and pollution degree, the characteristics of kinds of pulp are analyzed in detail, and the GP pulp which is low cost, high-yield, no-pollution is chosen as the material of tableware. Based on material element analyzed, shaping technology is designed, the to and for single plane shaping equipment which is high shaping quality, high production efficiency and is easy to automatize is chosen. All kinds of measure are taken to solve the problems which are inequality in the shaping process of GP pulp, and dosage which matches with GP pulp is chosen. Some ways of fixing shape and heat up are analyzed, the technology of saving energy of heat pressing to fix shape being composed of oil heat and only one fixed shape in the mold is applied, with which it is high production efficiency, low cost to fix shape effectively, which saves energy 30 percent. In order to make the production line meet with material of GP pulp, measure are taken to solve the problem of pulp adhered to netlike molding which can lead to carry material difficult, the structure of fully automatic equipment is renovated, the loaded beam is optimizationally designed to make equipment structure compactand improve location precision and products quality. According to technologic flow and actual characteristic, Omron PLC is chosen as the core of the control system, proximity switch as detect unit take the place of touch switch, software is designed reasonably according to time order figure, hardware is simplified, the reliability of system is advanced, the stability of system is assured to make production order. Intelligence neuron PID system is studied theoretically which is made up of both neuron with self-organizing and self-learning function and ordinary PID with the characteristic of the simple structure and high stability, which can automatically tune the parameter with the change of system parameter, remain perfect performance.

按成本指标和污染程度分析各浆料的特点，选择低成本、高得率、无污染的磨石机械浆为原料，在原料组分分析的基础上，设计成型工艺，选择成型质量好、生产率高、易实现自动化的往复式单板成型机，采取各种措施解决GP浆成型不均匀的问题及选择与机械浆相匹配的助剂；分析几种定型方式和加热方式，采用定型效果好、生产率高、成本低的油加热与模内一次性定型相结合的热压定型节能技术，节能30％；为了使生产线适应磨石机械浆原料，采取相应措施解决由于粘网造成物料转移困难，对全自动设备结构进行改进设计，着重对物料传送系统的关键部件——承载梁的进行优化设计，使设备更加紧凑合理，提高设备的定位精度和产品质量；根据生产线工艺流程和现场特点，选用OMRON CPM1A型PLC为主核心，接近开关作为检测元件，替代有触点开关，选用可编程终端代替常规面板按扭，并按照时序图科学合理地设计软件，有效地简化系统硬件构成，提高系统的可靠性，保证系统的稳定性，从而使生产更加通畅有序；从理论上探索将神经元应具有的自组织、自学习要求与PID控制结构简单、稳定性好的全自动纸浆模塑餐具生产线的研究特点结合起来，构成神经元自适应PID控制器，当参数的变化时，系统能自行参数整定，保持优良的工作性能指标，满足实际需求。

Medium does not scale, congeal, sinter or carbonize on the surface, and so is ideal heating element for viscous, and heat sensitive liquid medium.

加热器管表面功率负荷低，介质不会在表面结垢、粘结、烧焦、碳化等，是粘性、热敏性液体介质加热的理想元件。

If the temperature control system of the tank is active with the sensing element exposed to vapor, the tank's heating medium may be circulating at maximum rate with the tank wall at maximum temperature.

如果处在蒸汽中的感温元件启动了温度控制系统，储罐的加热介质可能会以最大流量循环，罐壁处在最高温度下。

This thesis made simulations on the power consumption, interface concavity, the crucible and the heater temperature.

本论文针对各热场元件对能耗、界面凹陷、坩埚和加热器温度分别模拟分析。

Thermal heating systems and components using German HOTSET, long life, heating effect is good.

加热系统及感温元件采用德国HOTSET，使用寿命长，加热效果好。

Temperature range 40℃~100℃±1℃. Heating element in contact to device bottom side.

温度范围40℃~100℃±1℃。样品承载台上的加热装置与元件背面接触加热。

Applying the casing tube of immersion heater made of this alloy to the hot-dip galvanizing industry, the examination of the industry show the casing tubes usually rupture after running about 50 days.

将该材料制成的热镀锌内加热器外套管直接应用于热镀锌的内加热设备上进行工业试验，元件在工作50天左右时出现意外断裂。

Plate, diamond tools graphite mold, sinter mold geological drill bits, industrial furnace, hot isostatic pressing equipment A variety of graphite heating elements, a variety of body heat, heater and production of monocrystalline silicon heater and shield, etc..

条。板，金刚石工具石墨模具、地质钻头烧结模具、工业电炉、热等静压设备的各种石墨发热元件、各种发热体、加热器及生产单晶硅的加热器和屏蔽罩等。

Designing the system schematic diagram explained the work principleof the hydraulic pressure synthesized testplatform; According to the design of hydraulic pump, hydraulicvalve, drill tubing choice and the computation, determined themodel and the size of the hydraulic pressure part; In order toimproving the consummation system, this articlealso carried on to test the system pressure loss and temperatureincrement; In addition, through the system calorific capacitycomputation, completed to choose the heater and the chiller ;Through designing the belt transmission and the axis structural,this article completed to the design of pumping station.

通过对系统原理图的设计，说明了液压综合试验台的工作原理；根据对液压泵、液压阀、油管等液压元件的选择和计算，确定了所需液压元件的型号及尺寸；为了改进和完善系统，本文还对系统压力损失和发热温升进行了验算；此外，通过对系统发热量计算，完成了对加热器和冷却器的选择；通过对带传动设计和轴的结构设计、校核，完成了对泵站的设计。

Self-Exciting Mode Oscillating-Flow Heat Pipe, also called pulsating heat pipe or oscillating heat pipe, is a novel heat transfer device that has an excellent heat transport performance.

自激振荡流热管也称为脉动热管，是一种新型高效的传热元件。本文提出了采用脉冲加热代替常规连续热源加热强化自激振荡流热管传热的方法，并对其进行了实验研究。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了