加热

Scandia Professional is an electric heater designed with special heating elements suited for frequently used sauna rooms.

斯堪的专业是一个电加热器加热，特别为经常使用的桑拿房设计适合的元素。

Based on the radiation characteristic of air speedy object, taking into account the synthetic influence factors of the real configuration of object, sun radiation, space long-wave radiation and the environment radiation around object, a further study for the effect of scarfskin pneumatic heating up, used equivalent resistance to estimate inner heat-resource and gave prominence to the influence on scarfskin radiation caused by engine heat-scattering, a logical and effective IR imaging simulation model for airplane is presented in this paper.

从红外辐射和热传导基本定律出发，综合考虑目标实际结构、太阳辐射、天空长波辐射、气动加热及周围环境辐射等因素的影响，依据空中快速目标热辐射特性，分析气动加热对飞机蒙皮辐射的作用，运用等效热阻对内热源部分进行估算，突出发动机传热部分对飞机整体辐射产生的影响，并建立一种可靠实用的空中飞机红外成像仿真模型，仿真过程中结合对空实拍红外图像进行动态调整，目标模拟结果真实感较强。

Firstly, with the thermal conduction equations of second homogeneous boundary and non-homogeneous boundary condition,we gained the temperature distribution in and after the heating process of the absorbing cavity.

用第二非齐次边界条件和第二齐次边界条件的热传导方程分别建立了吸收腔在激光加热过程中和激光加热结束后的温度分布，利用模拟实验对激光照射吸收腔的过程进行模拟，得到内、外壁温度差的实验数据。

Induction self heat reflow technology has the obvious advantages of 3D selective heating and high heating speed for electronic interconnects.

感应自发热重熔技术在电子互连的应用中具有明显的三维选择性加热和快速加热等优点。

Effect of heat-treatment processing on the semisolid microstructure of AZ91D magnesium alloy produced by SIMA process.

加热速度应选择较大的加热速度，这样有利于组织的细化。

In the electromagnetic field that countercurrent inductor produces, the metal droplet that melts gets the role suspension of electromagnetism force in quartz pipe center and had been heated up continuously. When metal droplet of melting have been heated up certain temperature surface beginning gasification, metal vapor tension will raise follow temperature go up, is heated continuously can have plenty of metal atoms overflow metal ball liquid surface, at the same time, as the inert gas of cooling medium, all along with certain current velocity, sideswipe the metal droplet surface that melts. Metal atoms fly out liquid surface according to certain way form the atom cluster by the condensing of inert air current, merger and the collision between crystal nucleus pellet and atom cluster form the smoke flame of nanoparticle pellet eventually.

在逆流感应器产生的电磁场中熔化的金属液滴受电磁力的作用悬浮于石英管中央并继续被加热，当金属熔球被加热到一定温度时表面开始气化，金属蒸气压随温度的升高而升高，继续受热会有大量的金属原子飞出熔球液面，与此同时，作为冷却介质的惰性气体始终以一定的流速掠过熔化的金属液滴表面，原子飞出液面受冷后就按照一定的方式凝聚成原子簇，在惰性气流中形核并随之长大，颗粒、原子簇间的碰撞与合并，最终形成金属纳米颗粒的烟焰。

And give a close study of the smolder ing velocities of polyurethane foam under different heat fluxes.

分析对比了相同加热条件下的聚氨酯泡沫材料在有氧和无氧气氛下的升温过程，并对不同加热条件下的聚氨酯泡沫材料的阴燃传播速度进行研究。

Briefly, the main operations of steel rolling are: Heating: steel ingots or billets are heated to a proper temperature above the recrystallization temperature in a soaking pit or reheating furnace.

简而言之，轧钢的主要生产过程为：加热--钢锭或钢坯在均热炉或加热炉中加热到再结晶温度以上的某一适当温度。

If a long time not to drink and become cool, press the button of HEAT to start heating again until to boiling and issued a warning sound.

若豆浆较长时间没喝而变凉，按下再加热键HEAT，加热至沸腾，停止加热，发出报警声。

The mixing method to measure solid specific heat capacity generally uses steam heater to heat the measured metal block.

混合法测量固体比热容实验一般采用蒸汽加热器对被测金属块进行加热，但用它测得的金属块的温度不准确，从而导致比热容不准确。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。