加点
- 与 加点 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
The ECC theory was studied in this paper. Polynomial was used to complete the hardware design of all kinds of algorithm including multiplication, division, point addition, point doubling和 point multiplication in GF (2m).
本文研究了椭圆曲线密码学理论,采用多项式基实现了椭圆曲线在有限域GF(2m)中各种运算的硬件设计,这些运算包括乘法、除法、点加、倍点和点乘,并用软硬件结合的方式实现了ECC的加/解密流程。
-
The definition and stability criterion of resonant operating points in a CPT system have been described. A Poincarémapping model has been built up and its Jacobian matrix has been derived with the implicit function derivative rule and chain rule. Then the stability of the fixed points can be determined according to the eigenvalues of the the Jacobian matrix. It has been used to study an example push-pull CPT system with three resonant operating points.
文中给出了CPT系统中谐振点的定义及判断条件,建立了系统的庞加莱映射模型,并根据隐函数及复合函数求导法则,推导出了系统庞加莱映射周期不动点的雅可比矩阵,根据雅可比矩阵的特征值分布情况,即可判断各不动点的自治振荡稳定性。
-
Common Reflection Surface stack is a brand-new and special ZO imaging method, the theory of CRS stack stems from paraxial ray theory, the biggest difference between CRS stack and conventional ZO imaging method is that it consider a reflector R as a circular reflector segment Cr placed in the vinicity of reflector R, Cr can be seen as the second order approximation of the reflector. The CRS traveltime surface is the multi-coverage reflection response of the reflector mirror assigned to R.
共反射面元(CommonReflection Surface=CRS)叠加技术是一种全新的、特殊的零偏移距剖面成像方法,CRS迭加理论源于傍轴射线理论,它与普通的零偏移距剖面成像方法的最大区别是它认为地下反射层是由许多个小反射弧段互相叠合组成的,认为来自某反射点附近的一个邻域内的反射信息都可以对该反射点的成像作出贡献,因此对该反射点进行零偏移距成像时就应该聚焦更多的能量参与迭加。
-
The stress-strain curves of Cu-Zn-Al alloys at different temperatures have been plotted on the tensile machine with the aid of electrometry. The main results were as follows: 1. When specimens were deformed within the range of M_s and M_d, the critical stress for inducing martensitic transformation increased with the temperature, and there existed a linear relationship between them. 2. When specimens were deformed above Af, complete pseudoelasticity might be obtained theoretically, which might be damaged, h...
在拉力试验机上用电测法测绘了Cu-Zn-Al合金在马氏体相变点上下各温度的σ-ε曲线,所得主要结果如下:(1)试样在M_s与M_d之间加载,随着温度升高,诱发马氏体相变所需临界应力增大,且加载温度与临界应力之间存在着线性关系;(2)在A_f点以上加载,理论上可获得完全的伪弹性,但加载温度过高或应变量过大,均会损害伪弹性;(3)试样在M_s点上下温度区域变形,得到的伪弹性回复和形状记忆回复之和在80%以上,但在M_s点附近总回复量出现一极小值,且伪弹性回复在M_f点以下又有所回升。
-
In the test model, a new type joint connection of one-way hinge is put forward for achieving pure-hinge connection; In the shape forming test, because of the little post-tensioning forces, a new type loading method of twisting nut for drawing wire is put forward in stead of jack tensioning for solving the questions, such as super-tensioning and the nonuniform rate of loading; In the loadtest, a new type vertical loading system of multiple-point fixed pulley is put forward for solving the questions, such as more loading points and larger vertical force at one loading point.
试验模型中,为了实现纯铰接连接,提出了一种新型的单向铰节点连接形式;成形试验中,由于后张拉力较小,提出了一种新型拧螺母抽钢丝的加载方法,很好的解决了千斤顶易超张拉和加载速率不均匀等问题;承载力试验中,为了解决加载点较多、单点加载较大的问题,提出了一种新型多点定滑轮竖向加载系统。
-
In the test model, a new type joint connection of one-way hinge is put forward for achieving pure-hinge connection; In the shape forming test, because of the little post-tensioning forces, a new type loading method of twisting nut for drawing wire is put forward in stead of jack tensioning for solving the questions, such as super-tensioning and the nonuniform rate of loading; In the load test, a new type vertical loading system of multiple-point fixed pulley is put forward for solving the questions, such as more loading points and larger vertical force at one loading point.
试验模型中,为了实现纯铰接连接,提出了一种新型的单向铰节点连接形式;成形试验中,由于后张拉力较小,提出了一种新型拧螺母抽钢丝的加载方法,很好的解决了千斤顶易超张拉和加载速率不均匀等问题;承载力试验中,为了解决加载点较多、单点加载较大的问题,提出了一种新型多点定滑轮竖向加载系统。
-
Among many implement schemes of decoding, the one using chips is the fastest one. Specific decoding chips like FPGA or ASIC have parallel processing structures, which make them be much fit for being high performance data processing processors like Digital Filter, Fast Fourier Transform, Discrete Cosine Transform, etc, and also be the key part of high performance data processing systems. The implementation is synthesizable Verilog code at the RTL level. It is suitable for real time video applications.
在MP3 解码电路中,模块IMDCT 由三个子模块组成:IDCT子模块、加窗函数子模块、输出数据的叠加子模块。N/2 点的输入Xk 经IDCT 变换得到N 点的输出xi 的公式如下:将输出根据不同的块类型(有四种块类型,分别为普通、开始、结束、短型)采用不同的窗函数加窗,得到一个36 个点的输出(对于块类型为短型的块,单个小块的输出是12 个点,每三个小块组合成一个36 个点的输出)。
-
Based on the analysis of T-shapedjoints, loading-carrying capacity formulae of K-shaped inner-stiffened joints arepresented. At last application of inner-stiffened joints in two projects are introduced.
在T形加劲节点研究的基础上,再分析K形加劲节点的承载力,并对加劲节点在两个工程中的应用进行介绍。
-
The strain of sheet mainly occurs in loading end in the initial load. With the increase of load, the strain extends to the remote end; the bond stress gradually reduces from the loading end to the remote end; the peak bond stress locates slightly away from the loading end. For 16.3% moisture content, the effective bond length between BFRP and wood is 100 mm.
结果表明,加载初期,纤维布上的应变主要存在于加载端附近,当荷载逐渐增加时,应变也向加载远端增大;随着与加载点距离的增加,粘结应力逐渐降低;随着荷载的增加,粘结应力峰值位置向远离加载点方向稍有移动;在含水率为16.3%条件下,BFRP与木材的有效粘结长度为100mm。
-
B: It's kind of dead. Maybe you want toadd more graphics to jazz it up.
有点闷。也许你可以加点图让它变得生动有趣些。
- 推荐网络例句
-
As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.
每逢看到沃林顿那刚毅的脸,那乌黑、忧郁的眼睛,她便会相信,他一定作过不幸的爱情的受害者。
-
Maybe they'll disappear into a pothole.
也许他们将在壶穴里消失
-
But because of its youthful corporate culture—most people are hustled out of the door in their mid-40s—it had no one to send.
但是因为该公司年轻的企业文化——大多数员工在40来岁的时候都被请出公司——一时间没有好的人选。