加工方法

Taking the installation of lathe bed and vertical shaft of computer numerical control machine as a example, a new glue feed technology was introduced, which is a promising method compared to traditional technique.

以立式数控加工中心的床身与立柱的安装为例，介绍了灌胶工艺新技术；与传统工艺比较，灌胶工艺技术是值得推广的先进方法。

In this dissertation, first, based on theory of cutting tooth about the gleason spiral bevel gear, the equation of meshing in the process of cutting tooth, the surface equation of generating gear as well as the general tooth surface equation of the double circular arc spiral bevel gear, using GB12759-1991 type of double circular arc gear as a basic gear profile, a three-dimension solid model of double circular arc spiral bevel gear which has the good adaptability was carried out by used of Unigraphics software;Second, by researching of the algorithm about contact and collision as well as various contact types based upon Contacting Finite Element Method, a foundation was laid for selecting the contact type in analyzing contact stress of double circular arc spiral bevel gearing;Finally, through the connection port of PARASOLID between UG software and ANSYS/LS-DYNA software, the three-dimension solid model of double circular arc spiral bevel gearing obtained above in UG was imported into ANSYS/LS-DYNA, a finite element analyzing about contact stress of double circular arc spiral bevel gearing was carried out by applying new loading method.

本文首先基于格利森弧齿锥齿轮加工原理及切齿啮合过程中的啮合方程、产形轮齿面方程以及双圆弧弧齿锥齿轮的齿面方程，选用GB12759-1991型双圆弧齿轮基本齿廓为基准齿形，利用Unigraphics软件的建模功能，绘制了有较好适应性的双圆弧弧齿锥齿轮传动三维实体模型。其次，描述了应用有限单元法进行实体接触与碰撞问题算法的公式，研究了有限元分析中的各种接触类型以及双圆弧弧齿锥齿轮接触应力分析中所选择接触类型的依据。最后，通过UG软件和ANSYS/LS-DYNA之间的PARASOLID接口工具包，将UG软件中得到的啮合齿轮模型导入ANSYS/LS-DYNA有限元分析软件，给出一种新的加载方法，进行了双圆弧弧齿锥齿轮传动的接触应力的有限元分析。

In this paper, the relation between differential driven ratio accuracy and the common normal length error of cylindrical bevel wheel has been found by experimental method, which provides a efficient way for cylindrical bevel wheel manufacturer to control the common normal length error of the wheel.

通过实验研究，寻找出差动传动比的精度与斜齿圆柱齿轮的公法线长度误差的关系，从而为斜齿圆柱齿轮的加工提供一个可以控制斜齿圆柱齿轮公发线长度误差的有效方法

A numerical model for calculating geometric parameters of the insert pocket on a boring cutting tool with indexable inserts is presented using the constraint optimization approach offered by ANSYS.

采用ANSYS的约束优化方法，建立了可转位镗刀刀片槽几何参数优化计算的数值模型，使用该模型可得到在给定切削条件下满足设计要求并使镗刀前角值为最大而主偏角值为最小的镗刀刀片槽加工所需的几何参数；最后给出了优化计算实例。

The processing method of low-sugar buckwheat cake, by using buckwheat , sugar, water, baking powder was studied.

以荞麦、白砂糖、水和泡打粉为主要原料，对加工低糖荞麦蛋糕方法进行试验，通过正交试验，确定4者最佳添加量。

Study is aimed at box threads of Φ177.8mm drill collar to analyze and calculate drill collar box thread with different stress-relief grooves using finite element method, the stress concentration of thread end of 3 types of box threads is gained under same boundary condition and load.

以177.8mm钻铤母螺纹接头作为研究对象，用有限元方法对加工有不同应力减轻槽的钻铤母螺纹接头进行了分析计算，得出了3种不同母螺纹结构在相同边界条件和载荷作用下螺纹消失端的应力集中情况。

An algorithm has been developed to predict stability lobes in ball end milling to investigate the influence of normal direction angle at cutting point on the stability .

讨论了用球头铣刀进行曲面加工时共振安定界限的预测方法，重点分析了法向方向角对共振安定界限的影响。

On this basic, we use intelligent decision technology based on case reasoning to NC cutting parameter decision and analysis. According the characters of NC cutting parameter decision, we take decision based on NC techniques rule, cutting case matching based on similar degree and cutting parameter correcting based on rules to design and realize system. Combining many field technologies, it makes a unique method to resolve NC cutting parameter problem. This design pattern is a new thinking for NC cutting parameter process.

在此基础上，本文将基于实例推理的智能决策技术用于数控切削参数的决策分析，根据切削参数决策判断过程的特点，分别按照基于规则的切削加工方案决策—基于相似度的切削参数实例匹配—基于规则的切削参数实例修正的设计思路进行了系统设计和实现，多个领域的技术紧密结合，形成解决切削参数难题的独特方法，开辟了数控切削参数处理的新思路。

Nine cutting tests on sand in wide best sanding machine with three belts were conducted by orthogonal design.

应用正交设计方法，在三砂架上砂式宽带砂光机上进行了9次试验；应用拉丁方表进行计算，得到砂光机最佳工作状态，从而推广到木工机床普遍应用，以提高木材的加工质量。

In accordance with the change pattern of the frequency composition of the cutting vibration signal and the phenomena during cutting, it has been discovered that there is a "micro-breakage stage"between normal wear stage and rapid wear stage of cutting tools with significant signal characteristics.

本文对车削加工中若干重要状态（即刀具磨损、破损和切削颤振等）的在线监测方法进行了理论探讨与实验研究。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。