加工方法
- 与 加工方法 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
A new method for correcting graphic distortion was putted forward.
提出了利用Newton插值法修正加工图形变形的新方法。
-
Modern plant modulus manufacture provides best method to decrease cost. In any case, those construction methods of handicraftsman carving and chiseling can hardly complete proper building for the mass in a short due.
现代化的工厂模数化加工为降低建筑成本提供了最好的方式,那种耗费大量手工艺人精雕细凿的建筑生产方法无论如何也不可能在短时期内生产出适合大众使用的建筑。
-
Plasterboard is light weight, sound insulation, heat insulation, processing, construction method is simple and characteristics.
纸面石膏板具有重量轻、隔声、隔热、加工性能强、施工方法简便的特点。
-
The practical CAD technology to manufacture high accuracy relief grinding cutter s is put forward.
提出了方便快捷地加工高精度铲磨刀具的CAD实用工艺,给出了改善刀具切削性能和增加重磨极限的方法及计算实例。
-
This paper introduces the method of machining worm gear ,worm with standardized gear hobber.
介绍一种采用标准齿轮滚刀加工蜗轮、蜗杆的方法。
-
This treatment is particularly useful for hypereutectoid steels that must be machined.
此处理方法对必须机加工的过共析钢特别有用。
-
3Glass capillary gas chromatography is used in the analysis of n-paraffin distribution of the diesel,and according to the results of the cold filter plugging point test ,it is conclude that the impressibility of DFI to fuel is not only connected with the alkyl side chain and the polarity group of medicine oneself ,but also the n -paraffin distribution of the diesel ,the component ,technology and directions for producing of fuel and so on.
该方法具有合成线路短、产率高、成本低的特点;(3)通过使用毛细管气相色谱法测定柴油中直链烷烃的组成与含量,及柴油冷滤点(Cold filter plugging point 简称CFPP)的测定得出结论,DFI 对柴油的感受性不仅与药剂本身的烷基侧链、极性基团有关,也与柴油的直链烷烃的含量、馏分组成、加工工艺等有关。
-
The mathematic model of optimization allocation of tolerance values is established. In the model, the objective function of the optimization is production cost-tolerance function, and the constraints of the optimization are equation and inequation in the fifth chapter.
以加工成本—公差函数为目标函数,以第五章的等式和不等式约束为约束条件,建立了公差大小最优分配的数学模型;基于遗传算法研究了形位公差大小的最优分配方法。
-
It has an advantage of innocuity, non-residual and non-pollution which is not substituted by any general way. The performance of the sterilization and modification is very good.
具有无毒、无害、无残留、无环境污染的其他传统方法无可替代的优点,辐照加工过程可控制,灭菌、改性效果极佳。
-
The equation between 6-dimision forces and interelectrode gap is set up based on the principle of least square multi-variables linear iteration method.
对采集的数据处理后,利用最小二乘多变元线性回归的方法,建立六维力与加工间隙的关系方程式。
- 推荐网络例句
-
And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.
47:5 法老对约瑟说,你父亲和你弟兄们到你这里来了。
-
Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.
提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法,同时,采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。
-
Hey Big Raven, The individual lies dont matter anymore - its ALL a tissue of lies in support of...
嘿大乌鸦,个别谎言的事不要再-其所有的组织的谎言,在支持。