力矩的

By using solidworks software,The models of AOD converter shell and molten steel for obtaining the areal coordinates are created to make refined calculation about the tilting moment s of the new or old converters.

运用solidworks软件建立AOD炉及钢液的三维实体模型，以获取其重心坐标，并对新炉、旧炉倾动力矩进行了精确的计算，依据倾动力矩变化曲线提出了防止炉体自动倾翻的耳轴中心安全高度的合理位置。

The result of experiment validated the mathematical models and simulation methods. On the basis of theoretical models and experimental data, the least square technique was used to identify the indeterminable parameters in torque motor and parameters of magnetic fluid.

在理论模型和实验数据的基础上，用最小二乘参数辨识的方法对力矩马达中的不确定参数及磁流体参数进行辨识，从而对添加磁流体的力矩马达进行了实验建模。

We tested the knees at flexion angles of 0, 15, 30, 60, and 90with the following applied loads: 10 Nm varus moment, and 5 Nm external and internal rotational torques.21,22 To calculate the force applied in varus rotation testing, we took the desired moment (10 N.m) and divided this by the distance from the joint line to the point of force application in meters.

我们检测了施加力量10N.m的内翻运动和5N.m的外旋和内旋运动，各种运动的膝关节屈曲角度分别为0°、15°、30°、60°和90°。为了在内翻旋转试验时计算施加力，我们采用期望力矩(10M.m)，并将这种力矩分为从关节线到施加力点数米远的距离。

We also observed and measured the distance and section of some muscles such as long muscle of neck、long muscle of head、sternocleidomastoid、trapezius、longissimus、inultifidus、splenius、semispinal muscle of head、semispinal muscle of neck、anterior scalene、middle scalene 、posterior scalene et al. We achieved the moment of force and downloaded the force in the model .We also added gravity of head.

通过横截面积肌力计算法，测量尸体颈椎周围的主要肌肉：胸锁乳突肌、斜方肌、头长肌、颈长肌、肩胛提肌、夹肌、前斜角肌、中斜角肌、后斜角肌、多裂肌等的横截面积及其与颈椎纵轴的中心距数值，求得力矩值，直接或根据力矩等价公式间接的将肌力值加载于模型体表各点。

A direct yaw moment control controlling vehicle motion by a yaw moment which is actively generated by transversally distributed tire longitudinal forces is becoming one of the most promising means of chassis control for the improvement of vehicle active safety.

通过控制左右车轮上的驱动力和制动力，产生横摆力矩来控制汽车的横摆运动的直接横摆力矩控制技术，可以有效地提高汽车的操纵稳定性。

The basic working principle of a self-excited retarder was introduced briefly and the main circuits of its drive controller were detailedly designed. Based on brake torque gear and vehicle's working condition, the formulae for calculating SCR's conductive angle were strictly derived and the real-time control on brake torque has been realized successfully by controlling SCR's conductive angle.

论文简要介绍了自励式缓速器的基本工作原理并对其驱动控制器的主要电路设计进行了阐述，详细推导了基于制动力矩档位与运行工况的可控硅导电角计算公式，通过控制可控硅导电角实现了制动力矩档位的实时控制。

With rapid technological development of gearless permanent magnet synchronous, it is required that the weighting system is able to not only provide signals for under load and full load to prevent overload, but also present and feedback precise weight signal to transducer, which automatically adjusts starting torque of motor by weighting signal and starts elevator smoothly.

随着无齿轮永磁同步电梯技术的迅速发展，要求称重系统不仅提供轻载、满载信号、限制超载、更应能够给出准确的称重信号，将称重信号反馈给变频器，变频器根据称重信号，自动调整电机起动力矩，使电梯平稳起动，称重系统也由限制超载的辅助部件，转变成为实现电梯起动力矩补偿，防止起动侧溜的重要功能部件。

The needle would stop rolling to maintain the friction effect between the needle and tested tissue when this friction moment come to the driving moment of the friction coupler.

二、在驱动电机和刺激针之间设计一个摩擦耦合器，当刺激针和组织之间的摩擦力矩达到摩擦耦合器的驱动力矩后，刺激针就会停止转动并能保持住对组织的摩擦。

The maximum tilting force moment value can be obtained by analyzing the static resisting force moment at individual points on the track along which mixers move.

对混铁炉在其运行轨迹上的各个位置静阻力矩进行分析，可以找出混铁炉倾动时所需的最大倾动力矩，然后可以选定与之相匹配的电机、制动器，以达到产品的优化设计。

The maximum tilting force moment value can be obtained by analyzing the static resisting force moment at individual points on the track along which mixer s move.

对混铁炉在其运行轨迹上的各个位置静阻力矩进行分析，可以找出混铁炉倾动时所需的最大倾动力矩，然后可以选定与之相匹配的电机、制动器，以达到产品的优化设计。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。