力矩

Close the valve, the need to open and close with the Coma Berenices two pieces of the sealing surface of the seal formed between certain specific pressure, while also overcoming the stem and the packing between the stem and the nut thread Automatic Control Valves between the stem end bearing at and other friction parts of the friction, and therefore must apply the closing force and closing a certain moment, the valve in the open and close the process, the required hoisting hoisting force and moment of change, and its maximum is close to the final instant or open the initial transient.

关闭阀门时，需要使启闭件与发座两密封面间形成一定的密封比压，同时还要克服阀杆与填料之间、阀杆与螺母的螺纹之间、阀杆端部支承处及其他磨擦部位的摩擦力，因而必须施加一定的关闭力和关闭力矩，阀门在启闭过程中，所需要的启闭力和启闭力矩是变化的，其最大值是在关闭的最终瞬时或开启的最初瞬时。

Close discharge valve, the need to open and close with the Coma Berenices two pieces formed between the sealing suce sealing certain specific pressure, while also overcoming the stem and the packing between the stem and the nut thread between the stem end Department and other friction parts bearing friction, and must exert a certain degree of closing force and closing moments, PUMP CONTROL VALVE EN700X the valve in the open and close the process, the required hoisting hoisting force and torque is the change, Its maximum is in the closed or open end of the initial transient instantaneous.

关闭放料阀门时，需要使启闭件与发座两密封面间形成一定的密封比压，同时还要克服阀杆与填料之间、阀杆与螺母的螺纹之间、阀杆端部支承处及其他磨擦部位的摩擦力，因而必须施加一定的关闭力和关闭力矩，阀门在启闭过程中，所需要的启闭力和启闭力矩是变化的，其最大值是在关闭的最终瞬时或开启的最初瞬时。

If a body is in the absence of any external torque, the angular momentum of the body is a constant. This is known as law of conservation of angular momentum.

如果物体所受的合外力矩等于零，或者不受外力矩的作用，物体的角动量保持不变，这个结论叫做角动量守恒定律。

The constraint force/torque dexterousness is defined as the ratio of minimum singularity value to maximum one of the force/torque constraint matrix, by which the performance of the combinations of actuating inputs is evaluated.

将约束力/力矩矩阵的最小奇异值与最大奇异值之比定义为约束力/力矩各向同性度，并以此为指标对各驱动输入组合的优劣性进行评价。

The paper presented that braking moment of disk brake was important for hoisting safety, and introduced the principle and method using a displacement transducer and PC to monitor braking moment on line.

阐述了盘式制动器制动力矩对提升安全的重要性，介绍了一种利用位移传感器和工控机在线监测制动力矩的原理和方

In static design of the control system, the influences of three-axle unintersect, unverticality and disturbance moment to the simulator's position accuracy is analyzed, and the error analytic formula is suggested. The influence of system static and dynamical friction moment, distinguishability of D/A convertor to the low-speed characteristic of the simulator is also analyzed.

在控制系统的静态设计过程中，分析了三轴转台的三轴不相交度、三轴不垂直度和干扰力矩等对转台位置精度的影响，并求出了误差的解析表达式，分析了系统的静、动摩擦力矩、D／A转换器的分辨率等对转台低速特性的影响。

In this paper,a numerical solution for radial journal bearings with liquid hydro-dynamic lubrication is analysed, numerical expressions for oil fiton pressure, bearing capacity , friction moment,and leakage at the bearing ends are derived,bearing capacity,flow rate, friction moment,and eccentric angle of the load under 14 different temperatures and 14 different load eccentricities are calculated.

采用数值法分析解算液体动压向心滑动轴承，推导了油膜压力、承载力、摩擦力矩和端泄流量等的数值表达形式，计算了14个不同温度点及14种不同偏心率下的承载力、流量、摩擦力矩、载荷偏位角，并通过AUTOCAD绘制了它们之间的影响曲线。认为偏心率及油温对承载力影响很大，设计时应加以限制。

The muscle samples were taken and check under microscopy and electro-microscopy,Desmin was checked with imunohistochemistry technique,maximal isometric titanic force,CK and LDH in blood,MDA and SOD in muscle were assessed for rats,before and after exercises to show muscle damage,maximal isometric torque,muscle soreness, circumference of the arm,range of motion of the elbow were assessed before and after exercise to show muscle damage,maximal eccentric torque, optimal angle of the elbow,total work during exercise were also assessed for college students.

观察指标包括：肌肉活检光镜及电镜观察，肌肉骨架蛋白Desmin组织化学荧光标记，电刺激最大强直肌量，血清LDH、CK及肌肉MDA、SOD等；等长峰力矩MIT，肌肉酸痛度SOR，肢体围度CIR，关节活动范围ROM，运动中离心峰力矩及其对应关节角度、所做总功等。

Calculation of the inertia force and inertia force moment on the drive ring plate and tumbler eccentric axis shows that the inertia force and inertia force moment of the reducer's driving mechanism are fully equilibrant.

传动环板及转臂偏心轴惯性力和惯性力矩的计算结果表明，这种减速器传动机构的惯性力和惯性力矩理论上是完全平衡的。

According to"Coal mine Safety regulation"the request,this article mainly analyzes the relation between the hoist's brake torque and brake deceleration in the equipollent tail rope promotion system,produced the relational curve of deceleration and the gravity characteristic coefficient and the braking moment multiple.

根据《煤矿安全规程》的要求，通过对在等重尾绳提升系统中制动力矩与制动减速度关系的分析，给出了减速度与重力特性系数和制动力矩倍数的关系曲线。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。