力矩

This explained that the knee adduction moment during late stance contributed 32% of the variance in knee pain.

这解释了站立后期的膝内翻力矩造成了关节痛中32%的差异。

Steering knuckle is one of the most important car key parts and a security part. It supports the body weight, transfers steering moment and endures braking moment of front-wheel.

转向节是轿车关键零件之一，为安全件，它既支撑车体重量，又传递转向力矩并承受前轮刹车制动力矩，因此对其机械性能和外形结构要求非常严格，制造难度大。

Starting Torque and work great torque motor operating current large, generally 80 ~ 120mA range.

起动力矩及工作力矩大，电机工作电流大，一般在80～120mA范围。

The diode's on and off process is simulated, too. Reason of generator's starting resisting torque and its regular rule are analyzed.

小型风力发电机提出了起动阻力矩的概念，本文对起动阻力矩进行了定性分析和定量计算。

The disturbing torque caused by carrier perturbation in the control system of seeker stabilized platform and the swing caused by sight angular angle were analyzed, the influence o f selection of different output dot of sight angular speed on sight angle and decoupling and the requirement for cont rol system transfer function were analyzed.

在稳定平台控制系统中分析了载体扰动产生的干扰力矩及对视线角引起的摆动，分析了选择不同的视线角速度输出点时对视线角速度、隔离度的影响及对控制系统传函的要求，为选择电机输出力矩、选择陀螺量程及控制系统传函的设计提供了理论依据。

The transformation of the yaw moment under differential brake and the impact of the slip ratio and road surface friction coefficient to the yaw moment were analyzed. The distribution method of the brake force was confirmed. After analyzing the observability of the control system, the state observer was designed, the evaluation of the side slip angle was completed and result of the evaluation wan validated.

本文分析了差动制动时整车横摆力矩的变化情况，研究了滑移率和路面摩擦系数对横摆力矩的影响，确定了制动力的分配原则，进行了控制系统的可观性分析，并设计了状态观测器，完成了质心侧偏角的估算并对此估算结果进行了验证。

Clearly, in order to provide sealing damper force, stem nut torque transmission valve operations than the big moment in the process.

显然，为了向闸板提供密封力，阀杆螺母传递的力矩比阀门操作过程中的力矩大。

The switch position of butterfly disc is limited by the adjusting screw pole on the worm gear transmission device.

蝶板的开关位置都由蜗轮传动装置上的调节螺杆限位，一级传动上的行程机构同时切断电机电源，如果超过密封所需的力矩，一级传动上的力矩控制装置立即脱落，同时切断电源。

The maximum tilting force moment value can be obtained by analyzing the static resisting force moment at individual points on the track along which mixers move.

对混铁炉在其运行轨迹上的各个位置静阻力矩进行分析，可以找出混铁炉倾动时所需的最大倾动力矩，然后可以选定与之相匹配的电机、制动器，以达到产品的优化设计。

The maximum tilting force moment value can be obtained by analyzing the static resisting force moment at individual points on the track along which mixer s move.

对混铁炉在其运行轨迹上的各个位置静阻力矩进行分析，可以找出混铁炉倾动时所需的最大倾动力矩，然后可以选定与之相匹配的电机、制动器，以达到产品的优化设计。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。