剪切角

Now the pushrod can be attached to the horn, measured, bent, cut and attached to the servo with a FASLINK.

现在的两个可以附加非洲之角，测量，弯曲，剪切和重视伺服与FASLINK 。

Based on the experiment, a finite element analysis model is established to predict the longitudinal shear modulus of X-cor sandwich structures.

在实验基础上，建立了X-cor夹层结构有限元分析模型，分析了Pin植入角、Pin直径以及Pin分布密度对X-cor夹层结构剪切模量的影响。

RESULTS: The biomechanical parameters (maximum torsional momentque, torsion angle and shearing elastic modulus) of Wistar rat's femur irradiated with 15 and 20 kGy were almost the same with that of control group in torsion test.

结果：15，20 kGy辐照组与未辐照组扭转试验的生物力学测试最大转矩、扭角和剪切弹性模量结果相近，差异无显著性意义。

Received the asphalt mixture mechanics performance index with frequency through FSCH test, it point out that the complex shearing modulus: G*, G*/sind can appraise the high-temperature performance of different asphalt mixture well. But phase angle: d can't relatively produce quality of high-temperature performance of every asphalt mixture obviously.

通过FSCH试验得到不同频率下沥青混合料力学性能指标，指出复数剪切模量G*、G*/sinδ能较好地评价不同沥青混合料的高温性能，而相位角δ不能明显地比较出各沥青混合料高温性能的优劣。

Received the asphalt mixture mechanics performance index with frequency through FSCH test, it point out that the complex shearing modulus: G*, G*/sind can appraise the high-temperature performance of different asphalt mixture well. But phase angle: d cant relatively produce quality of high-temperature performance of every asphalt mixture obviously.

通过FSCH试验得到不同频率下沥青混合料力学性能指标，指出复数剪切模量G*、G*/sinδ能较好地评价不同沥青混合料的高温性能，而相位角δ不能明显地比较出各沥青混合料高温性能的优劣。

Because of being shear forming process, the relationship between the thickness ofthe deformed region, the thickness (t0) of the raw sheet, and the angleαbetween sheetmetal forming surface and vertical direction z conforms to the sine law, i.e.,t = t0 sinα.

由于金属板料数控渐进成形工艺的变形是剪切变形，故其板料变形区厚度 t 、板料初始厚度 t0及半锥角α等三者的关系符合正弦定律，即 t = t0 sinα。

In order to obtain symmetry and parallel polarized light,the double Wollaston prism is amended. After getting symmetric polarized light at a big splitting beam angle,an ordinary triangular prism is added so that the symmetric light beam can be divided into parallel light beams.

为了获得对称且平行分束的偏振光，对双Wollaston棱镜进行了修正，在获得大分束角的对称偏振光后，配合普通玻璃三棱镜，使对称分束光变成平行分束光，通过改变三棱镜与双Wollaston棱镜间的距离来改变平行光的剪切距离。

In order to obtain symmetry and parallel polarized light, the double Wollaston prism is amended. After getting symmetric polarized light at a big splitting beam angle, an ordinary triangular prism is added so that the symmetric light beam can be divided into parallel light beams. The distance between the triangular prism and the double Wllaston prism is changed so that the distance of the shearing parallel light can be changed.

为了获得对称且平行分束的偏振光，对双wollaston棱镜进行了修正，在获得大分束角的对称偏振光后，配合普通玻璃三棱镜，使对称分束光变成平行分束光，通过改变三棱镜与双wollaston棱镜间的距离来改变平行光的剪切距离。

Influences of initial cohesions and friction angles on shear bandpatterns and entire deformational characteristics were investigated.

目的研究初始内聚力及摩擦角对剪切带图案及岩样全部变形特征的影响。

The hypo-volcanic crytoexplosion Breccia rock body and the felstone in the east-western shear zone are the important symbol of the exploration.

东西向脆－韧性剪切带内次火山隐爆角砾岩体、霏细岩脉的存在是区内重要的找矿标志。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。