制造法

Workshop is ventilated the optimal program that drop in temperature: Below torrid weather, because heat is conducted, heat radiation, did not adopt drop in temperature the indoor temperature of measure wants 10C -20C of prep above outside, manufacturing activity cannot on the rails.

车间透风降冷的最好方法：在酷热气侯下，因为热传达、热辐射、未实行降冷行动的房内温度要高于外面10C-20C，制造项目沒法正常施行。

Depending on the research of ABC and AAM , the authors aim is offering a reference for the application of our manufacture enterprises .

本文旨在通过对作业成本核算法、基于作业基础的成本分析和基于作业基础的决策研究，为我国制造企业应用作业成本法提供借鉴之处。

The key technology of "fattyacid-oil process" in production of alkyd resin is the alcoholysis of oils. The alcoholysis of fattyacid-oil is the result of esterification of fatty acid and alloholysis of oils, of which the medium effect of esterified product of fatty acid and polyols will promote the alcoholysis of oils with polyols.

制造醇酸树脂的"脂肪酸－油法"的技术关键依然是油脂的醇解，整个脂肪酸－油脂体系的醇解是脂肪酸酯化与油脂醇解并行反应的结果，其中，脂肪酸与多元醇的酯化产物的介质效应有力地促进了油脂与多元醇的醇解反应。

Methods: The two methods of nonsolvent process and solvent process were adopted to prepare oxamyl. Oxamyl was prepared in water in the first one and in acetone in the second. By the comparisons of productive cost, production purity, operation safety and equipment cost, a proper process for preparation oxamyl was adopted.

制取杀线威有两种不同方法，即非溶剂法和溶剂法，前者采用水为反应介质，后者采用丙酮为反应介质，从产品制造成本，产品纯度，操作环境的安全性以及生产设备投资等方面进行比较，确定可行的合成方法。

Stone Golem Manual: The book contains geas/quest, limited wish, polymorph any object, and slow. The reader may treat her caster level as three levels higher than normal for the purpose of crafting a stone golem.

石魔像手册：该手册包括反魔法力场，指使术，震撼法印及缓慢术，并且为制造者在制造石魔像时视为比实际施法者等级高三级。

Stone Golem Manual, Greater: The book contains geas/quest, limited wish, polymorph any object, and slow. The reader may treat her caster level as three levels higher than normal for the purpose of crafting a stone golem.

高级石魔像手册：该手册包括反魔法力场，指使术，震撼法印及缓慢术，并且为制造者在制造高级石魔像时视为比实际施法者等级高三级。

The worms reincarnate among the texts and make some interesting holes in them.

虫子从法本中长出来，并在法本上制造了一些有趣的洞。

Manufacturing methods are cold spring roll and hot roll method.

弹簧的制造方法有冷卷法和热卷法。

The closed-cell aluminum foam was fabricated by direct foaming in melt. Through sampling aluminum foam in different stages the cross-section of them were observed and analyzed. It was explained how TiH_2 was decomposed after entered into the melt, how initial bubbles were formed and what was the state that generated bubbles and undecomposed TiH_2 lay in.

以熔体直接发泡法制备闭孔泡沫铝材实验为基础，通过获得不同实验阶段的泡沫铝样品，以及对实验样品切面或断面进行观察和分析，描述了在熔体发泡法制造泡沫铝过程中TiH2加入熔体后的分解过程，原始气泡的形成方式以及产生的气泡和未分解TiH2的存在状态；解释了气泡进一步长大的原因和未分解的TiH2如何释放气体；表述了气泡的合并和无泡层的形成。

Based on the relevant movement between hard shaper cutter and grinding wheel, the movements of grinding wheel are studied. The shaping grinding point and the shaping grinding edge are made up with. In order to easily compare when shaping errors and cutting edge"s angles are the most excellent, uniform expressions for convex curved rake face of hard shaping cutter and spatial cutting edge curve are separately developed. The distributions of new profiling cutter"s shaping errors and cutting edges angles are analyzed. The relevant grinding wheel and cam are designed. Due to this paper, a new profiling hard shaping cutter has been manufactured successfully. At last experiments are made to test the performance of hard shaping cutter and all kinds of precision of hard gear.

本文直接从插齿刀与砂轮之间的相对运动关系出发，单独研究砂轮的运动，提出砂轮成形磨削点和砂轮成形磨削刃的概念；分别建立圆柱砂轮和圆锥砂轮磨削后硬齿面插齿刀的波形前刀面方程及空间切削刃方程；为便于比较何种情况下插齿刀的构形误差和切削角度能同时达到最优，分别对磨削五种不同硬齿面插齿刀所用的砂轮进行了廓形设计，并分析了插齿刀的构形误差和侧切削刃切削角度的分布规律；为插齿刀波形前刀面的磨削加工设计了相应的凸轮，用所设计的凸轮和近似的砂轮成功地制造出新构形法硬齿面插齿刀；最后进行插齿加工试验，检验新构形法硬齿面插齿刀的抗崩刃能力、耐磨性及被加工硬齿面齿轮的各项精度。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。