制造法

Should be able to work with Engineers for making any new fixtures, flanges required for testing.

能和工程师合作制造测试所需的新的夹具，法兰

Using phase mask to fabricate fiber gratings is a simple and effective method.

用相位掩模法制造光纤光栅是一种简单、有效的方法。

Through research and analysis of data, it was observed that the length and width of bark fiber varied according to the lop and age, the results show the fiber of the Salix bark is longer than the Salix and width of fiber almost same, fiber length of the Salix bark mainly influenced by the times of lop. The ash in Salix bark,1% Sodium Hydroxide Solubility in Salix bark, water solubility in Salix bark, Ethanol-Toluene in Salix bark, acid-insoluble lignin in Salix bark changed with the lop and age is also been investigated, the component of Salix bark is higher than Salix except acid-insoluble lignin,and it's high effected by times of lop; the TG analysis and DSC analysis is been used on the Salix bark and Salix to study the character of the hot-action, and the rang of the pyrogenate temperature is confirm; the quantity of Salix bark effect on the MOR, MOE, swelling in 24h water, nail withdraw and inner strength was determined, the results show that the Salix bark notability effect on the properties of board and dropped it; the properties of the Salix bark board is nearly the board product by other bark residues, it was established the multi regression equation of each properties and optimized the fitting produce condition of Salix bark board.

通过试验和数据处理，得出了沙柳树皮纤维长度、宽度随平茬和材龄的变化规律，结果表明沙柳树皮长度要比沙柳材的要长，宽度基本相同，沙柳树皮纤维长度主要受平茬次数的影响；找出了沙柳树皮中灰分、冷热水抽出物为、1%NaOH抽出物为，甲苯乙醇抽出物、酸不溶木素与平茬次数和材龄之间的关系，除酸不溶木素外，其他成分均明显高于沙柳材，沙柳树皮的化学成分主要受平茬次数的影响；利用TG和DSC法分析了沙柳树皮和沙柳材的反应热特征，确定了热解的温度范围；研究了沙柳树皮量对于刨花板MOR、MOE、吸水厚度膨胀率、握钉力以及内结合强度的影响，结果证明沙柳树皮量对于刨花板的各项性能指标影响显著，它的掺入降低了刨花板的各项性能；对沙柳树皮板的研究表明，沙柳树皮板的各项性能与同类树皮板的性能基本相近，建立的二次回归模型稳定，并利用回归方程求出了适宜的沙柳树皮板制造工艺。

Corner tappings - These are generally used on smaller orifice plates where space restrictions mean flanged tappings are difficult to manufacture.

角tappings -这些通常用于规模较小的孔板空间的限制意味着法兰t appings难以制造。

Information from other methods may be necessary, because some solvates are known to be stable temperatures above the boiling point of the solvent.

制造和储存原料药的条件可能会导致离析或形成溶剂化合物或水化的原料药。这通常可以通过干燥法制界检验，或者通过卡尔菲舍滴定法检验。

It was concluded that the expanding limit of the diameter of the pipe coupling exceeds 6%, while more than 80% of the degree of the memory recovery is achieved.

RROC法制备的TiNi首次直接用于制造管接头的研究，制备管接头的扩径变形率大于6％，形状恢复率大于80％，接近实用水平。

This paper introduces the principle and classification of mechanical balance,the allowable amount of unbalance and balance precision in the process of mechanical manufacturing,the balance testing method and its principle,the dynamic balancing system,and digital signal processing technology for rotating parts.

介绍了机械平衡的原理及分类，以及机械制造过程中允许的不平衡量和平衡精度，并对回转件的平衡实验法及原理、动平衡测试系统以及数字信号处理技术作了介绍，根据动平衡理论分析了平衡测试技术在生产中的应用。

This site provides introductory information to ore microscopy with over 30 full colour photomicrographs used in the course MICROSCOPIE DES MINERAUX OPAQUES at the University of Geneva.

该网站提供了一些有关矿石显微镜法的介绍性信息，并提供了由日内瓦大学制造的30张完整的彩色显微照片。

Based on the technology of machining the tooth profile of hobbing shaving cutter for cutting hardened gear, the approximate forming of the tooth profile on normal section is carried out by means of straight line fitting, arc fitting and hyperbola fitting.

基于硬齿面滚剃刀齿形的制造方法，分别采用直线、圆弧、双曲线拟合法对滚剃刀法截面齿形进行了近似造型。

METHDOS: Pulp cavity perforations were created in the pulpal floor of 55 extracted tooth. They were repaired with amalgam、flowable resin、Chinese gall compound recipe under amalgam、Chinese gall compound recipe under resin and MTA. Then the sealing ability of different materials by dye penetration were evaluated.

在55个离体牙上制造髓室底穿孔模型后，分别用银汞合金、复合树脂、复方五倍子作屏障银汞合金修复、复方五倍子作屏障复合树脂修复及MTAMTA组）修复，通过染料渗漏法测定各组渗漏情况。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。