刨花

The test results show that the performance of ISD will improve with the increase of air temperature, mass flow of air and initial moisture content of wood particles and the decrease of air humidity and mass flow rates ratio.

研究结果表明，随着气流温度的升高、气流湿度的下降、气流流量的增加、刨花初含水率的提高及载带率的减小，刨花对撞流干燥的强度也随着提高。

Research on the effects of different operating parameters of the new OSB blender on the performance of OSB made by blended particle was conducted.

研究新型定向刨花板拌胶机的不同工作参数对拌胶刨花压制成的OSB板子性能的影响，试验结果表明：拌胶机滚筒的装载量以刨花占滚筒容积15%为宜，最佳转速为13 r.min-1，采用抄板气流流态控制和针滚机械干涉方法，均能使刨花处于良好的受胶状态，胶液均匀分布，提高板子的力学性能。

With the premise of that valid chip forming area (the valid uniplanar inductive area of capacitance sensor) keeps stable, experiment results showed that with the definite forming height and density of chip when the moisture content varied in ranges of 5% to 25% were definite, the moisture content was exponent function as measuring frequency; when the moisture ranged in 25% to 45%, there was linear relationship between measuring frequency and moisture content of chip.

在刨花的有效铺装面积保持一定(即为电容传感器的有效平面感应区)的前提下，试验表明：当刨花的铺装高度和密度一定时，刨花的含水率5≤MC＜25％，测试频率与刨花的含水率成指数关系：刨花的含水率25≤MC＜45％时，测试频率与刨花的含水率成线性关系。

The article tries to provide the academic and experimental basis for establishment of technological parameters, design of the equipment and industrialization of ISD of wood particle, fiber and pulp etc forestry products.

本文试图通过以上的研究为刨花、纤维、纸浆等林产品的对撞流干燥工艺参数的制定和干燥装置的工程设计提供理论和实验依据，并为进一步实现刨花等林产品对撞流干燥的工业化奠定基础。

The strands were made by planning slicing and pressure slicing with Cunninghamia lanceolata as material and their dimension and shape were analyzed.

以杉木 Cuninghamia lanceolata生材为原料，采用平刨法和压刨法制备长形刨花，并对刨花尺寸和形态进行分析。

The glueyness of chips was increased and particleboard resin content could be decreased by 1-1. 5% because of the increase of the free radical concentration of chip surfaces.

结果表明用蒸汽压力1.275N/mm〓的蒸汽处理5min后的刨花表面自由基浓度均提高了，这样有利于刨花的胶合，并能使施胶量减少1-1.5%。

The function of cutting knife was to cut bamboo strands from a bamboo piece. Before they were cut off, a scoring-knife was used to precut a deep groove in the bamboo peice to section the strands.

切削刀片的作用是将竹刨花从竹毛坯上切下，但在竹刨花被切下之前已被定长划线刀片在竹材表面划出一定深度的槽沟，切断竹材纤维，使被切削下的竹刨花自然形成分段状态。

Finally, he air velocity, the velocity of the wood particle, the relative velocity between the air and the wood particle, the wood particle's residence time and the variations of the particle's velocity along radial and circle are measured. The ISD of particles is analyzed on dynamics.

最后，测量了气流速度、刨花速度、刨花与气流间的相对速度、刨花在半环内的停留时间及刨花在半环内沿径向和周向的速度分布，并地基础上进行了刨花对撞流干燥的动力学分析。

Finally, the air velocity, the velocity of the wood particle, the relative velocity between the air and the wood particle, the wood particle's residence time and the variations of the particle's velocity along radial and circle are measured.

最后，测量了气流速度、刨花速度、刨花与气流间的相对速度、刨花在半环内的停留时间及刨花在半环内沿径向和周向的速度分布，并在实验基础上进行了刨花对撞流干燥的动力学分析。

Finally,the air velocity,the velocity of the wood particle, the relative velocity between the air and the wood particle,the wood particle's residence time and the variations of the particle's velocity along radial and circle are measured. The ISD of particles is analyzed on dynamics.

最后，测量了气流速度、刨花速度、刨花与气流间的相对速度、刨花在半环内的停留时间及刨花在半环内沿径向和周向的速度分布，并地基础上进行了刨花对撞流干燥的动力学分析。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。