切角曲线

First, the relative curvature of a certain curve at its first end and the directional angle of the first port tangent vector of that curve as well as the weight factor of the interpolation curve are given, then all the other control vertexes can be gotten by using the conditions of G continuity, and a method to construct transitional curves is also introduced so that we can get the closed interpolation curve which achieves G continuity globally.

首先给定某段曲线的首端相对曲率和该段曲线的首端切矢量的方向角以及插值曲线的权因子，然后利用G2连续条件求出其余控制顶点，并给出了构造过渡曲线的方法，得到了G2连续的闭插值曲线。

A method of construct a quadratic uniform B-spline curve through data points is given.If the relative curvature of a certain curve on the first control point and the direction angle of the first port's tangent vector is given,here can get the whole curve by using the character of the port of quadratic uniform B-spline curve.

提出了一种二次均匀B样条插值曲线的构造方法，首先给定某一段曲线首点的相对曲率和该段曲线的首端切矢量的方向角，利用二次均匀B样条曲线的端点性质，求出其余各段曲线控制顶点，来生成整条插值曲线。

Meanwhile, taking the mutual shading effect of the neighboring spans into account, the direct solar radiation of arc vault of both east-west and south-north oriented multi-span greenhouse at noon on the day of winter solstice was calculated using the curvilinear integral method.

对东西走向和南北走向的华东型连栋塑料温室采用曲线积分的方法，在考虑相互遮荫的情况下，模拟计算了在冬至日正午时各种拱顶切角双圆弧屋面的采光性能。

Based on a series of shear creep tests of discontinuous plane with regular dentation,the relationship between shear creep and different normal stress,shear stress,and slope ratio is obtained.

文章在规则齿形结构面剪切蠕变试验的基础上，分析了剪切蠕变随不同的爬坡角、正应力和剪应力的影响，拟合了剪切蠕变曲线，并将拟合的方程与Burgers模型的本构方程进行了比较分析，讨论了Burgers模型中剪切模量、粘滞系数的变化规律及其影响因素，取得了较为理想的结论，为结构面剪切蠕变本构方程的建立提出了较为合理简便的方法。

The macroscopic rheological parameters and microstructure parameters were closely related, it is helpful to explain the essence of multiple rheological properties through the analysis of which the wax evolution process and microstructure of the crude oil which is waxy and high viscosity; the yield time of gelled waxy crude oil monotone increases along with the decreasing of rate of shear (the time of stress effect prolonged), there was power function relationship between them, it can be expressed with ; when adding diesel oil to Sudan crude oil, dilute proportion bigger the eccentricity degree of paraffin particles were bigger too, that was to say the symmetry of wax crystal was better, the wax crystal form fabric more hardly when the intermolecular interaction was smaller; in the light of macroscopica, the fall extent of the abnormity temperature, solidifying point and viscosity could be larger along with the accretion of dilute proportion, as a result, it's rheological properties could be improved.

SD原油析蜡点为94℃，析蜡高峰为50～30℃，异常点为40℃；其蜡晶颗粒细小、对称性差，所以具有较大的比表面能，容易形成联生、联锁结构；损耗角曲线与储能模量曲线或损耗模量曲线的交点所对应的温度与原油凝点或倾点温度非常接近，大约在39℃左右；也就是说，含蜡原油粘弹特性曲线的交点可以表征其流动性；原油宏观流变参数与微观结构参数密切相关，原油析蜡过程及蜡晶微观结构分析有助于诠释易凝高粘原油多重流变特性的本质；胶凝含蜡原油的屈服时间随剪切速率的降低而单调增加，二者显然存在幂函数关系，可用关系式描述；当SD原油加柴油稀释处理时，稀释比越高，蜡晶颗粒的偏心度也越大，亦即蜡晶对称性越好，分子间作用力越小，蜡晶颗粒越不易形成结构，宏观表现为异常点、凝点及表观粘度等流变参数下降的幅度越大，流动性越好。

The shape of curve could be modified to satisfy the demand simply through the amendment of the first end curvature or the directional angle of the first port tangent vector or the weight factor of a certain curve.

该方法可以通过简单地调整某段曲线的首端曲率或该段曲线的首端切矢量的方向角或该段曲线的权因子对曲线进行调节。

The database of judging chip break is founded, which is based on the characteristic of chip breaking curve.

通过切削试验，获得了刀具主偏角、切削速度和工作材料牌号对切屑的极限进给量和极限背吃刀量的影响规律及其经验公式，并根据切屑折断曲线建立了判断切屑是否折断知识库和切屑折断预报系统。

Predicting the up-curl chip breaking of three-dimensional groove inserts;2. The database of judging chip break is founded, which is based on the characteristic of chip breaking curve.

通过切削试验，获得了刀具主偏角、切削速度和工作材料牌号对切屑的极限进给量和极限背吃刀量的影响规律及其经验公式，并根据切屑折断曲线建立了判断切屑是否折断知识库和切屑折断预报系统。

The performance curves of the experimental fan have been obtained and the flow field has been measured at the best efficiency point of each setting angle, in fixed plane downstream the rotor with a constant temperature hot-wire anemometer and a periodic multisampling and averaging technique by an on-line microcomputer.

对轴流式通风机在不同安装角时的流场变化进行了实验研究，得到了通风机的总性能曲线；并用固定在转子前、后测量平面的热线，测量了最高效率点处不同安装角时叶片通道进、出口轴向和切向速度的分布，从而能够清楚地了解到，通风机在安装角变化时，叶片通道进、出口截面流动结构的变化。

The cutting pattern and load curves of cutting process of the two cutting heads were given by computer simulation, which showed that the cutting performance of the cutting head with pick arrangement based on equal-rise-angle spiral line was good because of its reasonable pick cut, its uniform cutting pattern and the small value and the fluctuation of its load.

为了评价利用等螺旋升角进行截齿排列设计的截割头的截割性能，选用了一个实际的截割头进行比较，通过计算机仿真获得两个截割头截割过程的切屑图和载荷曲线，经比较分析表明，用等螺旋升角排列截齿的截割头截槽合理，各段切屑图均匀，载荷大小及其波动较小，截割性能良好，所以用等螺旋升角排列截齿是一种高效、实用的截齿排列方法。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。