切角

Paper feeder,two pieces of upper and lower plate for die cutting, one set of allen key.

送纸机、模切上、下板各二件、六角匙一套。

For the Miami Zoo, the company delivered 15,000 of its patented "CyberCenes," which are printed on clear vinyl and attached to a die-cut folded, 18-pt.

对于迈阿密动物园，该公司交付15000其专利的& CyberCenes ，&这是印上明确乙烯和附加到模切折叠， 18角。

The test also shows that torque has not big change by using difference augers'tip and different angle of soil cutting blade on the end of auger's spiral wing.

不同钻头钻尖结构，不同切刀刃角在3种典型造林地的试验表明，这些因素对钻孔阻力矩的影响很小。

Our results demonstrate that the symmetric and asymmetric variations above the incident azimuths appear on the radial and transverse components of the receiver function, respectively.

结果表明，当台站下方存在倾向一致的倾斜界面时，远震体波接收函数的径向分量和切向分量分别随震源方位角的变化呈现对称和反对称的规律性变化。

Besides, theoretical arrival azimuths were computed by using the velocity model from a previous tomographic study.

同时利用以前研究中得到的剪切波速度模型计算了Love波到达台站的理论偏离情况，大多数理论计算与实际观测结果的偏离方向基本一致，但理论偏离角通常小于观测值。

The third one is characterized by brittle deformation of the eclogite blokes and strongly ductile shearing of the matrices,and developed at the middle satge(210-180Ma) and at amphibolite facies condition, in chich the UHPR was extruded and exhumated to the middle crust by the compression between the South and North China blokes.

第3期变形产生于角内岩相条件下，是折返中期（220-180Ma）超高压变质岩为南北陆块持续碰撞所挤出并向北逆冲至中地壳的结果，从榴辉岩的布丁化和基质的强烈韧性剪切为特征。

The relationship between field of view and departure maneuver is developed.(2) The departure trajectory and safety characteristic are discussed for V-bar departure, R-bar departure and arbitrary direction departure.

1研究了视场约束下V-bar撤离的径向和切向冲量方案，利用解析和数值结合的方法得到了冲量大小和视场角的关系；(2)针对V-bar分离、R-bar分离和任意方向分离，分别研究了分离后的相对轨迹及被动安全特性。

Basically include following production item: NC of ● of cut of ● CNC laser, punching, the treatment that fold a turn cuts, group of gold of Ban of solder of treatment of design of die of ● o

重要包括下面创造工程：●CNC镭射切分、冲孔、折弯处理●NC剪切、剪角处理●冲模策划处理、氩焊钣金组立●槽钢槽体处理、机器箱体组立●通信机架、器具创造●各式掌控箱、监视桌、笔记本电脑器械架开拓创造●瓦斯烤肉炉、食物加温配置●风机、排风配置咱们的联系方法事务部：闻美女：0512-65628938-210孟同志。

The results show that the main cause of the angular distortion of the lap joint is the non-uniform distributed inherent shear strain component that is vertical to the weld line and exists in the plane paralleling to the weld line.

结果表明：搭接接头焊接角变形的产生主要是由焊缝及其附近区域与焊缝平行的平面内垂直于焊缝方向上不均匀分布的固有剪切应变分量引起的。

The main rock types are two mica quartz schist and plagioclase amphibole schist.

老湾金矿床赋矿围岩是经历过多次韧脆性剪切改造作用的中元古界龟山组变质岩系，主要岩石类型为二云石英片岩和斜长角闪片岩。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。