切线的

The azimuth of the tangent line is the path of the ship.

此切线的方位是船舶的航迹。

Any more than crop marks it out in the crop marks to set aside a certain amount of margin (usually a 3 mm), so that people when trimming and cutting on the version of the microamounts are not allowed to be calibrated, this margin was bleeding.

任何超过裁切线的图像，必须在裁切线外留出一定的余量（一般为3毫米），以便人们在修整裁切时对微量的对版不准进行校正，这个余量就叫出血。

After a document is produced when you are finished, output if you use software default crop marks and permalinkjanuary setting, crop marks is located in the page to set the paper size "" may determine, if the paper size is too small is possible so that the document cannot be completely output to film.

制作完文档后，在输入时如果搁置软件默认的裁切线及页面新闻撤按时，裁切线的场所是根据页面撤定洋的"纸张不小小"所不决，如果纸张尺寸过小有不定使文档洋的不形式不克不及合座输入到胶卷上。

In the first part of the paper, we construct a family of 1 parameter cubic algebraic curves interpolating four given points and two tangent lines at the endpoints, and one can manipulate the shape of cubic algebraic curves by controlling the points or the tangent line directly.

该文提出的代数曲线的结构有两种，一种是插值平面上四点及两端点切线的三次代数曲线；另一种是插值两端点、两切线及两曲率的三次代数曲线。

The neuroanatomy of the eye.of or relating to or acting along or in the direction of a tangent.

属于、关于一个切线或切，沿着或向着一个切线的方向移动。

Pegasus needle, pedal normally take some time as the time after the step is tangent , and presser foot lift, but the workers said yesterday that the bottom line is easy when the needle off the tangent , tangent brandished a knife and I wanted to transfer about the time, but not know how to get in,...

飞马双针，踏板一般走一段时间像后踩的时候是切线，然后压脚抬起，可是昨天工人说双针切线的时候底线容易折，我就想调一下切线挥刀的时间，可是不知道怎么弄的，。。。

Pegasus needle, pedal normally take some time as the time after the step is tangent , and presser foot lift, but the workers said yesterday that the bottom line is easy when the needle off tangent , I wanted something fast time tangent brandished a knife, but not know how to get in,...

飞马双针，踏板一般走一段时间像后踩的时候是切线，然后压脚抬起，可是昨天工人说双针切线的时候底线容易折，我就想调一下切线挥刀的时间，可是不知道怎么弄的，。。。

Of or relating to or acting along or in the direction of a tangent.

属于、关于一个切线或切，沿着或向着一个切线的方向移动。

Height of top and bottom nozzles flanges from T.

顶部与底部接管法兰至切线的高度。。

Especially if you use normal napping and require the geometry data to contain tangents, the .x file format will not be very helpful.

特别是如果你使用并需要包含切线的几何数据，。x 文件就不是非常有用。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了