切屑

The new work supports are protected against penetration of swarf by a metallic wiper edge and sealed against liquids.

支持新的工作中不受切屑的金属渗透的优势，对雨刮液体密封。

This paper study on cutting force、average friction coefficient and swarf under this three cutting method ,the experimental results showed that oils on waterhave an effect on cooling and lubrication.

通过对切削力、平均摩擦系数和切屑形态的研究分析，揭示出微量油膜附水滴加工液具有良好的冷却润滑性能。

Manufacturers of machined parts look for separation solutions when packaging, storing and transporting goods, which have to have open apertures for oil and swarf to drain through while maintaining stability.

对机械零件制造商寻找分离时，包装，储存和运输货物，其中必须有石油缺口，并通过切屑排出，同时保持稳定的解决方案。

Low noises, no swarf, no exhaust gas , less pollution.

在生产过程中噪音低，无切屑、废气排出，污染很小，大大改善了工人工作环境。

It is then collected by the machine enclosure and guided back to the coolant reservoir via the swarf channels.

冷却泵将冷却液从液箱中打入管道、通过滑枕内部到达滑枕端面，然后由机床护罩进行收集并且借助切屑槽返回到冷却液箱。

Integral standard features also include an enclosed work area with a 600 CFM mist collection unit and a 40 gal recirculating coolant system with self cycling paper element swarf filtration.

整体标准外形构造也包括一个装有一个600CFM的水雾收集器的封闭式工作区域，和一个40加仑的带有自循环切屑过滤的循环冷却系统。

According to the request of construction features, processing spot, size precision, surface roughness and productivity that diesel engine air cylinder, sets the machine tool for single location horizontal type modular machine tool. Considered to the factor of the size precision, surface roughness, scrap removes and productivity and so on of the work piece, selects the Hard alloy not grind type surface milling cutter.

根据柴油机气缸体的结构特点、加工部位、尺寸精度、表面粗糙度及生产率等要求，确定该机床为单工位卧式组合机床；考虑工件尺寸精度，表面粗糙度，切屑的排除及生产率等因素，选用硬质合金不重磨式面铣刀；根据工件的尺寸、特点及其材料选择切削用量；然后，再经过切削用量来确定组合机床的通用部件；最后进行组合机床的总体设计。

On the basis of the empirical relationship between cutting forces and undeformed chip geometry, a three component f...

基于切削力与切屑几何之间的经验关系，用数值积分方法建立了球头铣刀三分量铣削力模型。

However, as the result of the particularity of the arrangement of vascular bundle in the nodal zone, in some cases, the cutting forces, chip form and the quality of the machined surface would be different from the internodal zone.

但由于竹节部维管束排列方向的特殊性，在某些情况下，竹节部的切削力、切屑形态以及加工表面质量都和节间材有所差异。

Yield rule, intensify rule, fluxion rule, types of contact and diathermanous model of metal cutting were also analyzed detailedly.

本文在直角自由切削过程分析的基础上，讨论了金属切削过程中的弹塑性变形理论和温度场理论，详细分析了屈服准则、强化准则、流动准则、金属切削传热模型、接触类型等问题，并利用有限元的基本思想，建立了直角自由切削应力场和温度场的有限元模型，进行了状态非线性、材料非线性和几何非线性的热力耦合分析，重点研究了切屑分离标准的确定、表面接触类型的处理等问题。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。