切向力
- 与 切向力 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
It means that pavement with camber is simply supposed to be horizontal.
由于横坡的存在,车辆荷载分解为垂直于路面的法向力和平行于路面的切向力。
-
Planet reduction shown in figure 6. Loose nut 6 "nut + washer + anti-loose nut". The explored view is Adjust torque 350~400N.m, rotate hub 13 at the same time. 5 and a radial force F=70N crease, hub can rotate free. Then fix lock washer into nut 6, fasten loose nut with torque 400N.m and make spacer control 0.05~0.15mm.
调整时,用 350~400N.m 力矩旋紧螺母 6,同时转动轮毂 13,使两轴承处于正确位置,然后,稍旋松螺母 6,在轮辋螺栓处施加一个切向力 F=55N.m,此时轮毂应能自由转动,然后装上止动垫片 5,将其卡爪折入螺母 6 的防转槽内,再用 400N.m 的力矩旋紧防松螺母,使轴向间隙控制在 0.05~0.15mm 之间。
-
Each of circular dishes is subjected to the action of a tangential force.
每个圆盘都受到切向力的作用。
-
It consists of three parts firstly,a large number of meshing data were measured out through three dismountable teeth installed along the radial direction of rigid wheel under loading status,secondly,the experimental curves of tangential force t and of radial force r inside meshing zone were gained by means of method of mathematica...
包括三部分:首先,在载荷状态下,通过安装在刚轮径向方向上三个可装、拆的活齿,测得大量的啮合数据;其次,通过数学统计方法获得啮合区内切向力Ft和径向力Fr的实验曲线;最后,应用函数逼近法获得载荷区内载荷分布方程
-
And the capacitor touch sensor has compact structure, high mechanical strength, and high flexibility, while the product can contact the surface with any curvature to sense the volumes of normal force and tangent force, and be applied for the production of flexile capacitor touch sensor array.
所制作的电容式触觉传感器结构轻薄,机械强度高,可挠性好,可贴附在任意曲率表面同时感受法向力和切向力的大小,同样适合由众多这种柔性电容式触觉传感器单元组成阵列的制造。
-
WC particles also can make the abrasive particles obtuse ,consequently reduce the cutting of abrasive particles to the coating.(7) The coating surface with unsmoothed units make the abrasive particles change moving direction . They can change the ploughing to rolling and bring light longitudinal vibration contributing to reducing the shearing force when the surface are worn by abrasive particles.
具有非光滑结构单元的复合层表面使参与复合材料磨损的磨粒改变运动方向,使之由滑动变为滚动,产生有利于减小切向力的法向微振动,减少磨粒和复合材料的接触面积和作用时间,从而大大减轻了磨粒对复合材料表面的损伤。
-
For example, before the slice force curve each step of cylinder is completed, force of inertia,top side gas force,shaft side gas force are required, per curve will possess 36 calculation spots at least.
尤其动力计算中采用非传统的解析法进行往复惯性力、盖侧气体力、轴侧气体力、切向力曲线的绘制使得压缩机切向力曲线的合成变得非常简便,计算过程解决的
-
Distribution of radial normal force and hoop tension force were discussed and equations derived. FEM analysis and experiments were carried out to verify the theoretical analysis.
对管材环状试样拉伸过程中试样的受力和变形进行了分析,采用正压力线性变化假设,推导了等宽环状试样的正压力和切向力计算公式。
-
The hoop tension force is axisymmetrical about the tension direction and increase from the top position to both sides. The distribution of hoop tension force is even with small friction coefficient, but will increase rapidly from top to side positions, which subsequently result in necking and fracture near the edge of gauge section.
结果表明:采用正压力线性变化假设所得的切向力分布规律与拉伸实验结果吻合较好;切向力关于拉伸方向呈轴对称分布,从正上方到两侧逐渐增大;当摩擦系数较小时,切向力分布较均匀,但当摩擦系数较大时,切向力从正上方到两侧迅速增大,试样的颈缩和断裂发生在标距段内靠近标距边缘的位置。
-
Based on a detailed analysis of the AFM diamond tip asperity cutting mechanism, in addition to the three-sided pyramidal diamond tip's geometry shape, a theoretical model is put forward for the case of calculating the normal force, cutting force, material flow strength and the frictional factor along the tip-workpiece interface.
提出了一个基于原子力显微镜三棱边金字塔形金刚石针尖的几何形状及与材料之间的单点切削机理所建立的理论模型,用以估算施加于金刚石针尖的法向力和切向力以及材料的屈服强度。
- 推荐网络例句
-
As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.
每逢看到沃林顿那刚毅的脸,那乌黑、忧郁的眼睛,她便会相信,他一定作过不幸的爱情的受害者。
-
Maybe they'll disappear into a pothole.
也许他们将在壶穴里消失
-
But because of its youthful corporate culture—most people are hustled out of the door in their mid-40s—it had no one to send.
但是因为该公司年轻的企业文化——大多数员工在40来岁的时候都被请出公司——一时间没有好的人选。