切下

Compared to several currently widely adopted turbulent lubrication theories, the present one is shown to be the best, in simple Couette-dominated regimes as well as in complicated regimes where commensurable Couette flows and pressure-induced flows coexist.

与当前广泛流行的若干个通用紊流润滑理论相比，无论在以剪切流为主的简单工况下或剪切流与压力流并重的复杂工况下，这个模式均为最优者。

The analysis of the results show as follow:(1)The consolidated-undrained creep, which doesn't include the volume strain, can be expressed by logarithmic functions as a type of under a different deviator stress.(2)The shear creep behaves in a linear elastic character in a lower stress level, and it is a nonlinear behavior in a higher stress level.

分析表明：(1)固结不排水蠕变中没有体积变化，不同偏应力下剪切蠕变可用对数形式表达；(2)固结不排水剪切蠕变在低应力水平下表现为线性粘弹性，而高应力水平时则具非线性的特性。

Aiming at the problems existing in the common bait methods such as bad cross-section quality and low efficiency, a new bar cutting technology based on high speed and restrained state has been put forward.

针对目前下料工艺质量差、生产率低和材料浪费等问题，提出了一种基于高速剪切和径向夹紧状态下金属材料精密剪切工艺方法。

In chapter 2, a tangent stiffness matrix formula of four-node C〓 element for the laminated plate is deduced, which is based on the first order shear deformation theory and the Von-Karman nonlinear deformation assumption.

第二章首先给出了在一阶剪切效应和Von-Karman大挠度理论下复合材料层合板的几何关系，然后基于单元域内和边界一致概念，推导了在大变形下"无剪切闭锁"的层合板单元切线刚度阵，并给出了复合材料层合板后屈曲分析的有限元平衡方程。

Results 12 single lower incisor absence patients, of whom 6 combined with tooth extraction;3 used interproximal enamel stripping and the rest 3 combined with prosthetics;16 double lower incisors absence patients,of whom 10 combined with tooth-extraction and the rest 6 combined with prosthetics.

结果：12例单个下切牙先天缺失患者中，有6例结合减数矫治，3例采用邻面去釉技术，3例结合修复方法；16例两个下切牙先天缺失患者中，10例减数矫治，6例采取缺牙修复。

Based on the Inglis formula, which calculates the tangential stress of the surrounding rock of geological stress field in different circumstances, programme is developed to compute the corresponding tangential stress of the surrounding rock of several underground plants, for instance, Ertan project of Sichuan according to different directions of longitudinal axle.

从地下洞室周边切向应力的英格里公式出发，提出针对不同环境的地应力场进行地下厂房纵轴线方位优选的简便方法，并编程计算了四川二滩等多个地下厂房不同纵轴线方向所对应的洞室周边切向应力，分析不同纵轴线方向条件下洞室周边切向应力的极值，并与实际工程所选取的纵轴线方向所对应的切向应力值比较，讨论了工程所选纵轴线的合理性以及洞室周边应力的集中程度。

Methods: Eight hundred normal cases were chosen randomly for study. Ultrasound was carried out in vertical section at xiphoid process, cross section at middle abdomen, and coronary section at the waist to detect the presence of AHV. The function site, number of AHV, caliber, flow velocity and the angle between AHV and IVC were investigated.

随机选健康查体者800例行超声检查，取剑突下纵切、右腋前线纵切、横切和中上腹部横切、肋间斜切，观察AHV的汇入部位、走向、数量、内径及其与下腔静脉轴线的夹角及多普勒波形、流速等。

Under torch brazing condition, using brazing filler metals of Cu-based and Ag-based, a series of tests are investigated to braze Ti based cermets and 45 steel, the micrographic structure of joints and shearing test results are analyzed, they show that Ti based cermets has good brazability.

通过观察和分析钎焊接头的结合情况及剪切试验，表明 Ti基金属陶瓷具有较好的钎焊性；火焰钎焊条件下，以 H 6 2为钎料的接头的平均剪切强度为37MPa，以 BAg10 Cu Zn为钎料的接头的剪切强度达 114 MPa，以 BCu Zn Mn为钎料的接头的平均剪切强度为 4 9MP

Second, on the basis of classical girder theory, girder element stiffness matrix considering shearing deformation is deduced, the method of calculation of value of shearing deformation is illustrated, and how far effect on inner force and deformation considering sheering deformation is discussed. Through comparison inner force and deformation between considerations in shearing deformation and not, several results are achieved and several suggestions to calculation are pointed out.Third, prestressed reinforcement is considered in the paper.

其次，在经典梁理论的基础上，本文推导出考虑剪切变形的平面梁和空间梁单元刚度矩阵，阐述了剪切变形系数的计算方法，讨论了在不同箱梁截面高度情况下，剪切变形对结构内力值和变形值的影响，并与不考虑剪切变形影响的结果作比较，得出有关结论，并对工程设计计算做出了一些建议。

The results indicate that the difference between the top and the bottom kerfs width of the die-board along eight directions is not sensitive to linear polarization with altering laser power and cutting speed, while the kerf width difference of steel is on the contrary.

试验结果表明，改变激光功率和切割速度对模切板进行切割，上、下切缝沿不同方向之间的宽度相差不大，即偏振性对高吸收率非金属材料模切板的切缝影响不大，但是对金属材料影响很大。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了