切

In an interview also remarkable for the strenuousness with which he sought to defend George Bush 's foreign policies, Cheney claimed the US had achieved "what we set out to do" in Iraq , and that the war had been "worth doing" because it had eliminated "the biggest threat" America faced in the wake of the 9/11 attacks.

今天的这次采访，还因切尼为布什政府外交政策作出的强力辩护而受人关注，切尼声称美国当初要在伊拉克实现的目标已经实现，伊战因为消除了美国在911袭击后面临的最大威胁而物有所值。

What I do, I cut this in strips, and then we gonna cut this...

我把这切成条，然后我们要去切这个。。。

Results 5 cases got total removal, 3 cases got subtotal removal, and 1 case got partial removal.

结果 全切5例，次全切3例，部分切除1例。

A "successive integration method" was firstly applied to the calculation of the plastic strain in large deformation analysis. By this method, it is easily to distinguish different resolved shear stresses and shear strain rate in different slip systems.

将"连续积分方法"首次应用到大变形弹塑性有限元分析中，使得晶体塑性模型能够区分出不同滑移系上分解剪切应力及相应产生的剪切应变，更好地反映金属材料塑性变形的微观特性。

And it is noted that the velocity field in a hydrocyclone is divided to two areas, i.e. the outer para-free-vortex and the inner para-forced vortex. The boundary surface of the velocity field is the maximum tangent velocity track surface, which is a cylinder when the hydrocyclones structure is reasonable.

分析研究结果表明，旋流器的切向速度场由外部准自由涡和内部准强制涡两个区域构成，其分界面为最大切向速度vtmax的轨迹面，结构设计合理时，此轨迹面为一圆柱面。

The aerodynamic characteristics of the cuted tip rhombus wing and double-delta wing of middling sweepback angle and aspect ratio about sixty type are investigated by a numerical method based on Eular equations.

采用Euler数值计算方法，对60多种中等后掠角及展弦比的切尖菱形机翼、双三角机翼纵向气动力特性进行了计算、分析和比较，从中筛选出16种切尖菱形机翼、14种双三角机翼进行了全机高速风洞实验研究，给出了机翼的展弦比、前缘后掠角、根梢比及几何扭转变化对全机升力、阻力及俯仰力矩的影响曲线和数据分析，在此基础上提出了用于定量估算两类机翼纵向气动力特性的关系式及修正因子。

Business consultants commonly warn their clients against becoming a symbiont company dependent upon a single customer-company, or a single supplier.

商务顾问常常警告其客户，切不可成为一个依赖单一客户的共生公司，切不可依赖单一的供应商。

In each step the tangent plane of limit state surface at the previous iterative point is calculated firstly, and then a line from origin to a point on the plane is determined whose intersection with limit state surface satisfies the requirement of feasible direction and convergence.

算法在每步迭代中先计算极限状态曲面在前步迭代点处的切平面，然后在此切平面上选定一个点，使该点和原点的连线与极限状态曲面的交点满足可行方向和收敛的要求。

The magnitude of each velocity component and tangential velocity curve changed a lot and the changes were even more obvious along as increasing of the valve lift.

各速度的大小和切向速度分布曲线发生较大变化，并随升程的增大而更加明显；对螺旋气道的动量矩流率影响较大，随升程的增加影响增大；对切向气道的动量矩流率影响更为明显，随着升程的增加影响减小。

The calculation results show that the normal component of magnetic intensity is symmetrically distributed around the point of the acting force, where the normal component reach the maximum value; while the tangential component is antisymmetrically distributed around the point of the acting force, where the tangential component inverses its direction sharply.

结果表明，空气中扰动磁场的法向强度和切向强度分布特征明显不同，法向强度关于力作用点对称分布，并且在力作用点处达到最大，而切向强度关于力作用点反对称分布，并且在力作用点处有突变；地磁环境下，磁场对位移的影响可以忽略不计；扰动场强与外力成正比。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。