切

The shear stress of particles is about 5% of the turbulent shear stress of the water.

颗粒剪切应力的数值约为水流紊动剪切应力的5％。

The shear stress and apparent viscosity of the masterbatch decreased with the increase of the shear rate and temperature.

随着剪切速率的增加，温度升高，剪切应力会降低，母粒的表观黏度也随之降低。

The feature of flow field and shear stress which is related to the atherosclerosis is analyzed.

计算不同时相、不同入口条件下的颈动脉窦流动场和壁面切应力分布，分析与动脉粥样硬化有关的流场特征和切应力特征。

These flakes, in turn, reduce the strength of the secondary shear zone, decreasing tool-chip interface and wear.

这些片状，依次减小第二剪切区中的力量，降低刀具和切屑接口处的摩擦和磨损。

The gold mineralization belt, mineralizing type and form of gold deposits were controlled by this ductile shear zone.

该剪切带对该区的金矿化异常带、矿化类型乃至矿床的形态和产状具有严格的控制作用，指出了韧性剪切带型应为本区金矿的主要类型。

Shear Limit - is the amount of force that can be applied before the material is sheared or twisted.

剪切限度是材料被剪切或弯曲前能被运用的力度。

The job can be done with simple cutting tools or by hiring a professional shearer.

这项工作可以通过简单的剪切工具或租用专业的剪切机来完成。

The results show that the amorphous PLGA fiber with porous structure (0.1-1.0 μm) is obtained by diluted solvent spinning method and the mechanical properties is affected by pressure and temperature. Bending strength and shearing strength of the samples increase firstly and then decrease with the increase of molding temperature and pressure. While the molding temperature is 160℃and the pressure is 105MPa, the PLGA materials possess optimal mechanical properties, bending strength, shearing strength and bending modulus 187.3 MPa, 100.0 MPa and 2.5 GPa, respectively. The mild temperature molding PLGA materials are desired to play a grate role in non-bearing internal fixation devices.

研究结果表明：非晶多孔结构的PLGA纤维可通过溶液沉析纺丝的方法获得，其孔径为0.1~1.0μm；压制压力和压制温度对材料的力学性能影响较大，材料的抗弯强度、剪切强度和抗弯模量均随着温度和压力的增大而先增大后降低；在压制压力为105MPa，压制温度为160℃时，试样的力学性能比较理想，此时，其抗弯强度可达到187.3MPa，剪切强度达到100.1MPa，抗弯模量达到2.5GPa，可望作为非承重部位骨折愈合内固定材料。

The shearing feature on plane Y was obtained and the mechanism of shearing deformaion was explained.

通过显微组织观察，得出了Y平面上的剪切变形特征，并解释了剪切变形的成形机制。

The results show that the additional shearing strain different from the normal compression deformation is generated in asymmetric rolling process. The more the different ratio of diameter,the greater the additional shear...

结果表明：在非对称轧制条件下会产生不同于普通压缩变形的附加剪切变形，而且异径比越大，产生的附加剪切变形也越大。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。