分段

We can lead out the equivalent border integral equation by Green the second equation,dividing the inner border in the liquid into a series strip of awls shell or cylindrical shell ,and solve border integral equation along different segment of border, then lead out border integral equation.

由Green第二恒等式导出等价的边界积分方程，将液体内边界分成一系列锥壳或柱壳状条，对边界积分方程进行分段积分，导出边界元格式方程。

The operation time was about 7~8 days. Stages of BBAF were backwashed separately depending on the status of each stage.

BBAF 的运行周期达7～8d，同时可根据实际需要采用分段反冲洗。

After the result of cohesion-friction model is compared with Coulomb Criterion, it is found that when the results of shearing strength are many and adjacent the strength parameters can not be regressed by least square method, instead the results should be divided into some beelines at that time according to the cohesion-friction model.(4) Discuss the characters of hard structural plane and weak structural plane: The adhesive friction theory is applied to research the changing course of shear area of hard structural plane and its influence on shear stress.

3介绍了岩石强度理论中的粘接摩擦模型，运用此模型分析依附型滑动面的演化过程，并将其推广到边坡岩土体抗剪强度的选取，讨论了不同法向应力下峰值强度和残余强度随法向应力的变化规律，在此基础上给出抗剪强度的选取模式，讨论了对实际取值结果的影响，并与传统的Coulomb准则进行了比较分析，指出直剪试验的法向应力在小应力区的点较多且抗剪强度结果差异不大时，不宜直接运用最小二乘法回归抗剪强度参数，此时应结合粘接摩擦模型对结果进行线性分段。

Introduce the cohesion-friction model of rock strength theory, and extend the model to select the strength of sliding plane, discuss the variation rules of peak strength and residual strength under different normal stress, and then present the selection model of shearing strength. After the result of cohesion-friction model is compared with Coulomb Criterion, it is found that when the results of shearing strength are many and adjacent the strength parameters can not be regressed by least square method, instead the results should be divided into some beelines at that time according to the cohesion-friction model.(4) Discuss the characters of hard structural plane and weak structural plane: The adhesive friction theory is applied to research the changing course of shear area of hard structural plane and its influence on shear stress.

3介绍了岩石强度理论中的粘接摩擦模型，运用此模型分析依附型滑动面的演化过程，并将其推广到边坡岩土体抗剪强度的选取，讨论了不同法向应力下峰值强度和残余强度随法向应力的变化规律，在此基础上给出抗剪强度的选取模式，讨论了对实际取值结果的影响，并与传统的Coulomb准则进行了比较分析，指出直剪试验的法向应力在小应力区的点较多且抗剪强度结果差异不大时，不宜直接运用最小二乘法回归抗剪强度参数，此时应结合粘接摩擦模型对结果进行线性分段。

The good agreement of theoretical data with test data shows that the creep damage evolution equation put forward is rational and the damage rheological constitutional model established can describe the accelerated creep stage of gypsum breccias well.

提出了&分段外推&的思想来提高神经网络模型对时间的外推性，同时，为了增加每段外推的稳定性，提出了&初次训练&的方法；以考题为例，验证了所提方法的优越性。

The relationships between the presintering process including the ratio of heating-up, presintering temperature and holding time to alumina and the machiningperformance of its presintered briquet were studied respectively.

分别讨论了改变升降温速率、预烧温度和保温时间与坯体加工性能之间的关系；采用1150℃预烧，保温2小时，及分段控制升温速率的工艺，获得了适合机加工的坯体，能避免加工时的断裂、破碎或崩边。

This article focuses on research of prediction of rock-burst happened in Cangling extreme long-tunnel engineering, comparison of tunnel carving details in the performing stage and prevention measures.

通过对苍岭特长隧道岩爆问题的预测研究和施工阶段洞身开挖情况对比，以及针对本工程的岩爆防治措施研究，探讨了岩爆预测判据对苍岭隧道工程的适用性，揭示了苍岭隧道围岩的岩性特征和初始应力场，掌握了苍岭隧道岩爆发生的烈度和基本分布规律，提出了对岩爆问题的工程防治措施，另外，根据工程区地质条件和岩石物理力学性能参数，建立了相应的地质力学模型，采用有限元法建模反演分析，其结果与通过钻孔水压致裂试验测得的地应力结果比较，显得较为吻合，并得到施工阶段通过洞壁应力恢复法分析结果的验证，验证表明理论模型和有限元模型的适用性及分析应力场是较为准确和合理的，并在此基础上对苍岭隧道岩爆进行分段预测和采取了较有成效的工程防治措施，具有较高的工程应用价值。

The object history is divided into three segments, and stored in different media with various chronons.

文章讨论了分段存储的特殊数据结构、时代转移算法和压缩采样算法。

On the Badaling is a majestic pass castle.the wall,made of granite stone slabs and special bricks, is 6-7m high,with a width of 4-5m at top.On the wall there are watch towers,crenels,embrasures,and drainage system.

古都北京城西北方屏障八达岭长城，是明代长城建筑中独具代表性的地段，岭上设有雄伟的关城，城墙用花岗岩条石和特制的城砖砌筑而成，高约6-7米，顶宽约4-5米，墙顶分段设置敌台、垛口和射击洞，还特设有排水系统。

It identifies "worse condition points" along the path according to the curve information, machine tools capability and machining requirement. Integrated with adaptive interpolation, segmented high speed machining is adopted. Different constant speed segments and speed transition segments are obtained according to the feed motion constraint model, and the corresponding feed information are stored in a penta-element lookup chain table. By referring to the lookup table, the interpolator can automatically determine the feed motion.

算法根据加工路径的曲线信息、机床加工能力及加工要求确定&最差状态点&，并结合自适应插补思想，采用分段高速加工，根据进给约束模型得到不同恒定速度加工段及速度过渡段，并将这些信息存储在一个五元的自适应Lookup链表中，插补过程中通过查找该链表确定进给参数。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。