分段

The main tool is the notion of the Lipschitz condition with positive non-decreasing integrable function L-average along the piecewise geodesic which includes theclassical Lipschitz condition as well as theγ-condition as special cases.

同时，我们在研究中引入了沿着分段测地线的关于取正值非减可积函数L-平均的Lipschitz条件的概念，从而把流形上的Kantorovich定理及Smale理论统一起来研究。

With domestic and oversea segment fuzzy controls in beer ferment,rarelyappear and popularized due to lack of intercommunity.

国内外很多研究者在啤酒发酵控制中采用了模糊控制技术，但并未采取分段控制的方法，或者因控制方法缺乏共性而难以推广。

According to variable flow rate testing analysis theory, in view of the pressure characteristics only appeared in intermittent production period in exploration wells, it gives the sectional calculation idea of steady flow, pseudo-steady flow and DST and provides the calculation methods of steady time and pseudo-steady time etc.. It realizes more accurate simulation of downhole pressure history and improves the accuracy of pressure history matching.

利用变流量试井分析理论，针对开发井间歇生产期才有的压力特征，提出了稳定流动、拟稳定流动及DST流动的分段计算思想，并给出稳定时间、拟稳态时间等计算方法，实现了井底压力历史的更为准确地模拟，提高了压力历史拟合精度。

In addition also using algebra interpolation leveling system error, including the linear interpolation, the parabola interpolation and the partition interpolation.

此外还利用代数插值法校正系统误差，其中包括线形插值法、抛物线插值法和分段插值法。

On the basis of error processing interpolation theory of non-circular curve and data processing function of Excel, an accurate model of curved parts can be made in Solid Edge with establishing the point curve in Excel.

研究了复杂曲线零件的精确建模，在研究非圆曲线插值算法理论的基础上，利用Excel的数据处理功能，对函数进行误差处理插值计算，在Solid Edge环境中使用Excel创建点曲线的方法进行曲线零件的精确建模，探索出了一种Excel与Solid Edge的完美结合方法，通过凸轮零件精确建模的实际案例，示出了曲线零件建模的整个过程，给出了这种方法在分段曲线中的具体应用。

In this method, corresponding data sheet of promissory truth-value and indicating value was set up and the measured value could be obtained by inverse operation.

该方法通过标准分段查询，即建立约定真值与示值之间的对应数据表，再经过逆运算就可以得到测量值。

The paper proposes a method of the piecewise water distribution of main canal according to the characteristic of irrigation canal in mountainous area.

针对山区灌溉渠道的特点，提出了干渠分段配水的方法，分别对来水充足和来水不足条件下的干渠配水进行了理论分析和实例计算，取得满意成果

The uncertainties for verifying all kinds of abraded straight rulers with different length on interferential installation with isoclinic circle fringe by two kinds plane optical bars were evaluated in this paper. Among the uncertainty evaluations, the situation of subsection also was evaluated.

摘 要：对不同长度的研磨平尺用两种不同长度长平晶在等倾干涉装置上检定的不确定度进行了评定，其中包括分段法不够一整段时的评定。

By this method, the vibration solution can be obtained in the form of power series and the iterative computation is not needed.

本文首次将幂级数求解变系数微分方程的方法引入齿轮振动方程的求解中，从而不需要将齿轮变啮合刚度分段常数化和反复迭代求解，就可以求出齿轮的振动微分方程的解。

With the piece-wise linearization for Volt-Ampere characteristics of nonlinear electronic device and the improvement of control strategy in iterative process, the computation efficiency of path planning is improved.

通过对非线性电子器件伏安特性进行分段线性化处理，并且改进迭代过程中的控制策略，使得路径规划方法的计算效率得到提高。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。