分析曲线

RESULTS: We built up two standard curves with the results of UV spectrophotometry and wet weight, to plate count, respectively. The analysis of accuracy rating proved that there was an approximal linear correlation between the two standard curves ranging from 105/mL to 108/mL.

结果： 建立了紫外分光光度计法和湿重法相对于平板计数法的标准曲线，通过准确度分析表明在细菌含量在每毫升105～108之间时，两标准曲线线性关系良好。

this article discusses the integral theorem of mean the promoted question, mainly has two aspects: On the one hand in analyzes in the teaching material under the first integral theorem of mean condition, had proven lies between the value spot to have to be possible to obtain in the open-interval, further discusses this knot promotes to the generalized Riemann integral, and further proved the conclusion also establishes to the promoted first integral theorem of mean; Promotes on the one hand in addition the integral theorem of mean to in the curve and the curved surface, and has proven the curvilinear integral theorem of mean and the surface integral theorem of mean.

本文讨论积分中值定理的推广问题，主要有二个方面：一方面在分析教材中第一积分中值定理的条件下，证明了介值点必可在开区间内取得，进一步将这个结论推广到广义Riemann积分，并进一步证明结论对推广的第一积分中值定理也成立；另一方面，将积分中值定理推广到曲线和曲面中，并证明了曲线积分中值定理和曲面积分中值定理。

Three cross-sections were made through crown and gingiva of the model tooth. Curve functions of axial buccal crown and gingiva contour of each section were acquired by means of curve fitting, and the angle of emergence pofile was calculated, which represents the degree of undercut.

以下颌第二前磨牙为研究对象，在牙列模型上通过牙冠部、牙龈作3个纵断面，用曲线拟和的方法得到每个断面的牙齿轴面外形及相应牙龈外形的曲线方程，以此分析两者之间的关系并计算牙冠起始外形角度，即倒凹程度的大小。

The measured voltage andits corresponding ceramic mud's argil content relationship was analyzed, whichwas nonlinear for ceramic mud of mass fraction between 0％～40％, and linear for ceramic mud of mass fraction between 40％～60％.

记录、分析这组电压值和陶瓷泥浆质量分数的关系后知道：含陶土量为0％～40％之间的数据曲线是非线性的，在陶土含量为40％～60％之间的数据曲线是线性的。

At the same time, utilize configuration controlling part and lens to control in real time, show the pressure real-time trend of mandril mold stripping , window autoalarm, write down historical value to show historical trend curve in helping technical worker analyse parameter to guide manufacture.

利用组态王开发友好的人机界面，利用组态控件和摄像头对生产现场进行实时监控，显示压力和顶芯力的实时趋势曲线，窗口自动报警，并记录历史值显示历史趋势曲线方便技术人员分析操作。

At the sametime, utilize configuration controlling part and lens to control in real time, show the pressure real-time trend of mandril mold stripping , window autoalarm, write down historical value to show historical trend curve in helping technical worker analyse parameter to guide manufacture.

利用组态王开发友好的人机界面，利用组态控件和摄像头对生产现场进行实时监控，显示压力和顶芯力的实时趋势曲线，窗口自动报警，并记录历史值显示历史趋势曲线方便技术人员分析操作。

In this thesis, we first discuss the algorithms of arithmetic operations over binary fields using a polynomial basis representation.

本文首先讨论了有限域上基本算术运算的算法，对有限域上的椭圆曲线理论进行了研究，分析了椭圆曲线上的核心算法——数乘算法。

For fitting ROC curves and getting the area under the ROC curve, we applied the parametric methods of binormal models and ordinal regression models, the semiparametric method of Cox proportional hazards model, the nonparametric methods of Hanley, Delong.

本文采用双正态模型、有序回归模型等参数法，Cox比例风险模型半参数法，Hanley、Delong非参数法拟合了ROC曲线；文中也考虑了样本量的估计、协变量的混杂效应、再抽样技术计算ROC曲线下面积的标准误与可信区间等问题；并研究了SROC分析方法。

Finally, using cross section method, the equationof product crash boundary curve of back peak zigzag pulse is deduced.

这种方法有两个明显的缺点：不仅费时费工，而且不便分析产品破损边界曲线的物理意义和把握这条曲线的几何特征。

Based on the analysis of the characteristics of the compensation directions for boundary curve s in rapid prototyping direct slicing, a new method, which can determinate the compensation direction by converting the boundary curve to beeline polygon,is proposed.

在分析快速成型制造中直接切片真实边界曲线补偿方向特点的基础上，提出了一种将曲线边界转化为直线多边形进行补偿方向判定的方法，并阐述了该判定方法的几何意义。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。