分布不均匀的

The results show that the shape of meniscus is non-homogeneous because of the structure of the rectangular mold, and the height of meniscus will enlarge as increasing the power, and at the same time the meniscus fluctuate aggregately. The coil should be placed near the top of the mold and the initial free surface level should be placed in the middle of the coil in practice.

结果表明：由于矩形电磁软接触结晶器本身的结构限制，其弯月面沿周向上的分布具有不均匀性；随电源功率增大，弯月面高度增大，同时波动加剧；实际生产中线圈应尽量靠近结晶器口部位置安装，有利于提高弯月面高度和增强弯月面稳定性；浇注过程中，应该使浇注液面尽可能的控制在线圈中心偏上位置；当电源频率增大时，应该同时适当的提高电流来保证软接触效果。

Experimental result makes clear, the main reason that structure of revulsive bursa bubble alters exterior activator is exterior activator embeds in the double element layer of bursa bubble, the inhomogenous sex that the exterior charge intensity that changed bursa bubble thereby and the exterior activator after embedding distributing in layer of bursa bubble double element.

实验结果表明，表面活性剂诱导囊泡结构改变的主要原因是表面活性剂嵌入到囊泡的双分子层中，从而改变了囊泡的表面电荷强度以及嵌入后的表面活性剂在囊泡双分子层中分布的不均匀性。

Unfortunately, the heat treatment process usually produces distortion of the gear, with the result that gear load is not uniformly distributed across the gear tooth face.

不幸的是，热处理过程通常会使齿轮发生扭曲和形变，这样齿轮上的载荷就不能均匀的分布到轮齿的表面。

Comparable to other methods, this algorithm mainly has four advantages:(1)It is effective and can be easily realized (2)The output is G -continuity surface (3)It is suitable for the object with arbitrary topology (4)It allows the distribution of data point sets asymmetrical.

与其他无组织散乱数据重建算法相比，本文算法主要有4个优点：(1)运行效率高，且思想简单易于实现；(2)输出结果为具有G 连续的曲面；(3)适用于任意拓扑结构的物体；(4)允许数据点集的分布具有一定的不均匀性。

The energy deposited by the particles can transfer directly or indirectly along DNA strand and the bonds of high affinity and low ionization potential respond firstly. As a result, the strand breaks and uneven distribution of breaks is formed.

原因可能在于沉积的能量直接或间接沿DNA链迁移，链上相对较弱的化学键优先产生反应，并最终导致链的断裂，从而引起断裂的不均匀分布。

But uneven deposition rate along the radius of the sample holder is also found by infrared analysis technology when sample is deposited in magnetic field profile,which is produced by the coil current with 137.7A if the SmCo permanent magnet is equipped under the substrate holder.

通过红外吸收谱技术分析，虽然样品台下面放置钐钴永磁体并使磁场线圈电流为137.7A下能得到最大的沉积速率，但是沿样品台半径方向沉积速率呈现很明显的不均匀分布。

But uneven deposition rate along the radius of the sample holder is also found by infrared analysis technology when sample is deposited in magnetic field profile, which is produced by the coil current with 137.7A if the SmCo permanent magnet is equipped under the substrate holder.

通过红外吸收谱技术分析，虽然样品台下面放置衫钻永磁体并使磁场线圈电流为137.7A下能得到最大的沈积速率，但是沿样品台半径方向沈积速率呈现很明显的不均匀分布。

Considering the uneven distribution of earth stress, the influence of mono-axis pressure on rock velocities is also discussed.

考虑到实际地层压力分布的不均匀性，本文还分析了单轴压力对速度的影响。

The research aim of this thesis is the winding end insulating structure of oil immersed power transformer 110kV . Beause of the very asymmetric electric field, the higher electric field would apeared in the oil-gap and partial charge will easily engendered in the wedge oil-gap between static ring and head block of winding end.The two-dimensional isoparametric and finite element method is used for analyzing and calculating the electric field distribution in high voltage winding end insulating structure.

本文以110kV油浸电力变压器绕组端部绝缘结构为研究对象，针对绕组端部绝缘结构中静电屏与垫块之间存在楔形油隙区，致使电场分布很不均匀，油隙区中的电场强度较高，容易产生局部放电的特点，采用二维等参元有限元法及有限元软件ANSYS电磁场分析功能对高压绕组端部绝缘结构进行电场计算分析。

The thicknesses of the layers between the active region and the ridge waveguide are optimized by taking into account the injected carrier distribution and local material gain in the SLD cross section.

考虑了注入载流子横向分布的不均匀，较准确地计算了模式增益。结果表明，通过对残留层和上光限制层厚度的优化，可以有效提高SLD与单模光纤的耦合功率。

The reasons of iron ions content overproof in grade Ⅱ desalting water system,such as variation water quality,contamination of regenerant , operation adjustment of pretreatment system and switching operation of bed were discussed.

对二级脱盐水系统中铁离子含量超标的原因，如来水水质发生波动、再生剂受到污染、预处理系统操作调整、床体运行切换等进行了论述。

You were hired to drum up new business, so go and do it.

公司雇你招徕新业务，你就做你的事好了。