刃
- 与 刃 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
For the all classes of dies, if we analyse the fluctuate, tendency of increase and decrease and law which appeared in the die's whole life, we will find that the master of the error are changeless; the error that because the abrade of the cutter and impression will be as the cutter grinding times increased at the same time. And that will cause the error oversize gradually; and also have another part error are unconventional , unforeseen.
对各类冲模冲件误差在冲模整个寿命中出现的波动、增减趋向及规律等进行全面分析便可发现:冲件误差的主导部分是不变的;因刃口或型腔的自然磨损而出现的误差增量随冲模刃磨冲数增加而使这部分误差逐渐加大;还有部分误差的增量是非常规的、不可预见的。
-
I Division is specialized in research and development of a series of drill grinding machine, cutter grinding machines, multi-blade sharpening machine and CNC rotary file grinder, and other special light tool grinding equipment companies.
我司是一家专业从事研制开发系列钻头刃磨机,铣刀刃磨机,多工位刀片刃磨机及数控旋转锉磨床等各类专用刀具修磨轻型设备的公司。
-
Its most major and most complicated problems are the analysis of drill point mathematical models and drill grinding theory, which is the foundation of drill grinder design.
而各种先进钻型数学模型的建立及刃磨理论的研究是钻头自动化刃磨技术的研究的重点和难点,它是钻头刃磨机设计的理论基础。
-
It analyzes the structure feature of all parts in the novel grinder and motion principles, which establish the base for producing the drill grinder. The research on grinding mechanism and development of the novel drill grinder fill the blank at home and abroad, which will bring large economic and social benefits.
新刃磨原理的研究和新型钻头刃磨机的研制,填补了国内的空白,类似原理的刃磨机国外也未见报导,将带来较大的经济效益与社会效益。
-
Employing the method of complex helical drill point design,the formula of the clearance angle of inner cut edge for the socket drill is derived and the relationship between the clearance angle and the slantwise angle of the inner cut edge is deduced to innovate the design and manufacture of the socket drill.
通过复杂螺旋面钻尖设计方法导出锪窝钻钻尖内刃后角公式及内刃后角与内刃偏角的关系表达式,改进了锪窝钻的设计与制造。
-
Whether you're sessioning the park or cruising the mountain for every possible tranny, the Quantum is not only performance driven with its Dual-Transitional sidecut and dual-density base, but it's a true twin shape designed to conquer every transition or jib. The highly elastic brass edges are designed for added durability and to keep your edges from cracking or catching on rails.
无论你是否曾经在单板公园耍酷或者是在雪山上巡航,这款板都不仅仅发挥出他那双重过渡的边刃以及加倍密度的板底,而且他还是一个地地道道的左右对称的板头设计用于征服每一个跳跃或者是跐杆,高弹性的黄铜刃将更加的耐磨并且能使你的刃在铁杆上不会被撞断或者被卡住。
-
Serrations create a semi-saw on the sharp side of the blade.
锯齿刃在刀片的刃边上创造了一个类似锯子的刃形。
-
Cografts point in general there are two: vertical tool grinder mill out of an arc-shaped blade angle, as in Figure 2 illustrated horizontal grinder mill out of cografts is straight, as in Figure 2 is shown below.
刃角通常情况下有两种:用立式磨刀机磨出的弧线型刃角,如图2所示;用卧式磨床磨出的刃角为直线型,如图2所示。
-
Does spiral movement synchronously,a nonlinear model was established by neural networks to describe the relationship between the helical groove and the milling cutter'sprofile,and according to the helical groove axial cross section to simulate the milling cutter's profile.
加工螺旋槽时,针对铣刀刃形的设计,应用包络面原理,采用神经网络方法建立了工件螺旋槽形与铣刀刃形之间的非线性关系模型,并通过工件螺旋槽端面截形模拟仿真出铣刀回转面刃形。
-
This paper presents the Machining Tool geometry of the former flank, the main flank, flank, the main cutting edge, Under the cutting edge tip cutting plane, the main section, the former Kok, horn, wedge angle edge angle, pointed knife, the blade angle, vice horn, Under the Frontier concept, the concept of cutting consumption, and the general circumstances of their choice method for processing slender shaft. cast iron materials, aluminum, stainless steel, rubber materials, plexiglass material, cloth bakelite materials, high temperature alloys, aluminum-magnesium alloy, hardened steel, the typical trapezoidal thread, the thread Triangle, Speaking at the trapezoidal screw thread pitch of the Tool geometry of the selection methods and cutting the amount of cutting fluids reasonable choice.
本文介绍了在机械加工中车刀几何角度中的前刀面、主后刀面、后刀面、主切削刃、副切削刃刀尖切削平面、主截面、前角、后角、楔角主偏角、刀尖角、刃倾角、副后角、副前角的概念、切削用量的概念、以及一般情况下的它们的选择方法,进行加工细长轴、铸铁材料、铝合金、不锈钢、橡胶材料、有机玻璃材料、夹布胶木材料、高温合金、铝镁合金、淬火钢、典型梯形螺纹、三角螺纹、特在螺距的梯形螺纹等的车刀几何角度的选取方法切削用量及切削液的合理选择。
- 推荐网络例句
-
I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""
客人们在卡罗利娜·埃凯家里,举止就文雅一些,因为卡罗利娜的母亲治家很严厉。
-
Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.
由著名品牌 Herm è s 设计,这件高贵的制服是香港本土制造,是我们第一套不配帽子的制服。
-
Do not 'inflate' your achievements and/or qualifications or skills .
不要 '夸大' 你的业绩或成果,条件或者技能。