刀具

The mechanism of glass cutting by single-straight tool with big inclination angle is presented, and the main technical parameters which affect the qualities of machined surface are discussed.

研究了大刃倾角刀具切削玻璃的机理及刀具参数和切削用量对已加工表面质量的影响。

The main process machinery and equipment are:(1) hit halo hemp electrical appliances, due to livestock and poultry species, varieties vary;(2) assassination put Xuedao, because different types of livestock and poultry, knives of different sizes, in order to ensure that medical and consumption of blood cleaning hollow knife can be used;(3) peeling or burning hair back hair machinery and equipment, medium and large slaughter plant machinery stripped of pigs, cattle, sheep skin, small factories and individual butcher knife while peeling by hand, Mao 60-68 ℃ hot hot hot flooding 3-8 minutes, easy to back hair, animal hair may be back with a different machine back hair;(4), cut open, cuts except internal organs, cutting off their heads and trimming hooves many different processes such as cutting tools complete with manual and electric saws and a half split two ways , hand-split and a half with machetes, saws chop and a half should be washed clean bone debris.

主要工序机械设备是：（1）击晕麻电器，因畜禽种类、品种不同而异；（2）刺杀放血刀，因畜禽种类不同，刀的大小也不同，为保证医用和食用血液的清洁，可采用空心刀；（3）剥皮或烫毛退毛机械设备，大中型屠宰厂用机器剥去猪、牛、羊的皮，小厂和个体屠户则用手工刀具剥皮，烫毛用60—68℃热水浸烫3—8分钟，便于退毛，畜禽均可用不同的退毛机器退毛；（4）开膛、剖除内脏、割头蹄和修整等工序多用不同的刀具完成，劈半有手工和电锯两种方法，手工劈半用砍刀，电锯劈半后应将骨屑冲洗干净。

As a result of cutting and high feed rate, HSC processing will normally be the life of the tool down paper, from the tool material, geometry parameters, stretching the length of the hanging, as well as cutting parameters and cutting geometry, cutting line, and other lubrication cooling to take measures to minimize the reduction of life expectancy.

由于切削和进给速度高，HSC加工中刀具的寿命一般会降纸，需要从刀具材料、几何参数、悬伸长度以及切削参数、切削几何关系、走刀路线、润滑冷却等各方面采取措施，尽可能减少寿命的降低。

This cutting tool was tested in dry-cutting area, and its cutting properties were studied to machine quenched steel.

将氮化碳涂层刀具应用于干切削领域，通过对淬火钢的干式切削试验，研究氮化碳涂层刀具的切削加工性能。

The company was established in 2000, in all kinds of metal-cutting tools, non-standard metal-cutting tool to undertake the design and manufacture for customers to provide technical help.

本公司成立于2000年，主要生产经营各种金属切削刀具，大量承接各种非标金属切削刀具的设计制造。为客户提供技术帮助。

Based on the parametric equations of blade surfaces and hub surface, and selected form specification of the ball end mill, we use MATLAB to calculate the coordinates of tool paths and tool-axis orientation.

本文系以叶轮叶片面及轮毂面的曲面参数方程式资料为基础，选定刀具形状规格后，应用MATLAB程式来计算刀具的刀尖点座标及刀轴方向。

Howeer, IT will not split moes, so if any part of a moe requires a change of feedrate, then the feedrate will be applied to the whole moe.

然而，由于IT不能够分割移动，所以如果刀具路径的某一部分需要改变的话，这个进给率就会应用到整个刀具路径中去。

The tool can hae an additional 'side-increment' feedrate, which is applied to step-oer moes.

刀具还可以设置一种边切进给率，以使用于横向的刀具移动。

The characters of contact lines on the rollers within four kinds of cylindrical cam mechanisms are analyzed first using the theory of conjugating surfaces and the conclusion got then that cylindrical cams ′ contours are not torses in this paper.

在此基础上，认为圆柱凸轮廓面在理论上只有用等径刀具才能精确加工，非等径刀具只能近似加工，并讨论了等径加工的合理方法以及非等径加工的研究方向。

Its basic operation method is a tight mother of the lock that the opens to face afterward, can transpose the angle of the pole of arbitrarily, can process the thread that the different helix rises the Cape, this kind of knife pole has the strength and tenacities to process to slice to pare the dosage exaltation labor rate of production and decline low cost etc. to have the progress towards increasing [10]the knife, improve it is a kind of price less that knife have, yielding results the quicker method.

其基本操作方法是拧开其后面的锁紧螺母，可任意调换蜗杆的角度，可加工不同螺旋升角的螺纹，这种刀杆对增加刀具强度和韧性加工切削用量提高劳动生产率及降低成本等方面有所进步，改进刀具是一种代价较少，收效较快的方法。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。