击穿的

The results showed that plastic deformation at both -70℃ and 180℃ made the dislocation density of AISI304 stainless steel increase with the increase of deformation. Martensite phase transformation was induced for deformation at -70℃, whereas it was not at 180℃. As the dislocation density increased, the breakdown potential of AISI304 stainless steel's passive film became a little more positive. As martensite phase content increased, it became more negative and pitting corrosion resistance decreased.

结果表明：加热180℃和低温-70℃条件下塑性变形均使AISI304不锈钢中位错密度随变形量增大而增加，AISI304不锈钢在-70℃条件下塑性变形时部分奥氏体相转变为马氏体相，而在180℃条件下塑性变形时不发生马氏体相变；位错密度的增加使AISI304不锈钢钝化膜的击穿电位略微正移，而马氏体相的增加使击穿电位呈负移趋势，材料耐孔蚀性能降低。

Then the breakdown mechanism was introduced to explain the results.It is found that the optimum polarity combination is heteropolarity and the best scope of the ratio between trigger voltage and self-breakdown voltage is 30%~50%.

实验结果表明：新型触发管开关获得最佳触发特性所需的极性组合应为异极性组合，触发电压幅值范围为自击穿电压的30%~50%，为兼顾触发电流和保护触发器，触发电阻值应为50~100 Ω，验证了触发管开关击穿机制的已有认识。

The operating principle and hardware configuration of the instrument based on AT89C51 for testing breakdown voltage of the dielectric oil is introduced. The method to collect the breakout current through photoelectric isolation is proved when the dielectric oil was broken out. The question about the system work stability in the condition of strive electromagnetism interfere is proposed.

介绍了 AT89C5 1单片机控制的绝缘油耐压测试仪的工作原理及硬件结构，探讨了在绝缘油击穿时，通过光电隔离采集击穿电流的方法，解决了在高压击穿瞬间和强电磁场干扰环境下，微机电路实行有效复位并使系统稳定工作的问题，给出了基于 MAX70 6为核心的高可靠复位电路的实现方法。

The results shows that the probability distribution of discharge striking points is related to the breakdown voltage,breakdown time and the development of head-on discharge, it is influenced by geometric shape of object, ground resistance, and geometric striking distance.

结果表明，放电击中点的概率分布与上电极对各目的物的击穿电压、击穿时间和迎面放电的发展有关，受目的物几何形状、接地电阻和几何击距等因素的影响。

At this point the zener diode conducts current in the revese direction, which maintaining the zener voltage across its terminals .

此时齐纳击穿两极管引导 revese 方向的涌流，维持横过它的终端机的齐纳击穿电压。

The US 76 mm gun, if firing the APCBC M62 ammunition, could penetrate the Tiger frontally out to just over 500 m, and could be at ranges in excess of 1,000 m to achieve penetration against the upper hull superstructure.

美国76mm炮，如果发射APCBC M62彈藥，可以恰好在500米击穿虎式正面，也能够在超过1000米的距离上实现对首上上部的击穿。

At last, arc reignition characteristic is defined for multiple-narrow slot chamber, and the mechanism of arc reignition process is analyzed. A mathematical model which forecasts the arc reignition process is improved for the first time by combining the striking theory of cathode layer with"black box"model for forecasting arc thermal reignition.

最后，通过试验确定了多纵缝陶土灭弧室中电弧重燃特性，对其机理进行了研究，并首次将阴极层击穿理论和预测电弧热重燃的黑盒模型相结合，建立了模拟陶土灭弧室中弧隙由电击穿到热重燃过程的电弧数学模型。

By discussing the influences of restriking phenomena, some effective methods are presented for restraining restriking phenomena and improving the performance of current limiting.

通过分析影响开断过程电弧重击穿现象的主、要因素，本文提出了几种抑制开断过程重击穿现象、提高断路器限流特性的有效方法。

Based on the discussion of some problems, it is pointed out that mountingadditional lightning arrestors on both ends of overhead lines is an effective means toprotect outlet CB of substations.

就事故分析提出了几个值得探讨的问题：事故与断口两侧有工频电源有关；雷击波的陡度值处于外绝缘大于内绝缘的区域和电压抽取装置的削波作用不显著而使灭弧室内绝缘击穿；外绝缘先击穿或内、外绝缘同时击穿；事故与雷击进线段发生绕击或反击的关系是主要的还是次要的。

Have discussed liquid dielectric breakdown theory and sundry factors influencing liquid dielectric breakdown voltage, and put forward electric spark discharge model.

论述了液体电介质的击穿理论，分析了各种因素对液体电介质击穿电压的影响，提出了电火花放电模型。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。