出孔

Guide, valve stem cap hole and implementation must be kept closed to keep within the allowable deviation of a tie, this will result in a smooth linear motion with no constraints, and spilled liquids.

导向器、阀帽孔和执行阀杆必须保持在关闭时的容许偏差内以维持一个配合，此配合将造成平稳直线运动而无约束和溅出的液体。

Lifting mechanism exterior adopts square welding structure, with installation bolts hole four sides and high usability, could be transformed into fixed or suspended bogie traveling electric hoist and 360°rope lead.

起升主机部分外罩为方型焊接结构，四面均有安装螺栓孔，通用性高，可快速改换成固定式或悬挂小车运行式电动葫芦，并可360°方向出绳。

On December 28, 2007, anxious furnace of Lai steel 2# goes out smoothly anxious, after put into production of 2# Jiao Lushun benefit, productivity of cooking factory coke will achieve 4.2 million T, become have rate of advanced technology, advanced equipment, automation the modern cooking system of tall, environmental protection, enter the throughout the country, shed cooking enterprise train. 2# Jiao Lu belongs to JN60-6 model, room of 60 aperture char, year design ability is 600 thousand T, with 1# Jiao Lu form a complete set is become group, its tooling, automation, environmental protection be in countrywide congener furnace banner level.

梗概： 2007年12月28日，莱钢2#焦炉顺利出焦，2#焦炉顺利投产后，焦化厂焦炭生产能力将达到420万t，成为具有先进工艺、先进设备、自动化程度高、环保的现代化焦化系统，进入全国、流焦化企业行列。2#焦炉属于JN60-6型，60孔炭化室，年设计能力为60万t，和1#焦炉配套成组，其工艺装备、自动化、环境保护等都处于全国同类炉型领先水平。

Tracing the pattern on cloth when after powder through the pin-hole. Fix the pattern on cloth for easy cutting.

用於纸样上刺孔，当扫&涂粉&后，覆印出纸样於布片上；用於将纸样固定於布片上，以便剪裁。

The hollow-axis motor drives the offset nozzle and rotates the arc on the tip of wire at high speed,so as to ensure enough penetration into the sidewalls in narrow gap welding .

在该系统中，焊丝穿过电机的空心轴后从导电嘴的偏心孔送出，电机带动导电杆和偏心导电嘴旋转，从而使焊丝端部的电弧以一定直径高速旋转，以保证窄间隙焊接接头具有足够的侧壁熔深。

Bottom line… if your wrist stays cupped during the exit of the thumb you cannot get revs. The thumb has to exit the ball cleanly.

最后一点…。。如果释球时还把手腕弓得鼓鼓的，是打不出好的转速的，姆指必需要乾净俐落地先脱出球孔才行。

The 3D elastic mechanics and finite-element structure analysis priniple were provided.The mechanics characteristics of the three-faced aluminous rotating mirror were analyzed,and the finite-element model was established.

给出了3维弹性力学空间问题基本方程和有限元结构强度分析原理，分析了三面体铝合金转镜空间结构强度的力学特征，建立了有限元模型，分析了其在轴孔与轴的3种配合关系下的应力分布。

The Nano-electromechanical sensors, such as membrane pressure sensor, four-beam accelerometer and bionic vector hydrophone, are fabricated successfully by micro control-hole technology, and they are measured in pressure tank, jarring table and standing wave tube respectively.

采用控制孔技术成功加工出了基于RTS的圆膜压力、四梁加速度和仿生矢量水声三种新型纳机电器件，并分别对其进行了压力罐、振动台和水下驻波测试。

This thesis describes the preparation of HTS rf SQUID, the design of the readout andthe innovation of our inductively coupled tank circuit. Using this tank circuit and ourreadout, we achieved the flux white noise of 15 〓/√Hz for an HTS YBCO rf SQUIDwith the loop size of 100×100 μ〓, and a field sensitivity of 24fT/√Hz by using a 1 inchwasher flux focusor.

文中描述了rfSQUID样品制备过程和我们所研制的rfSQUID读出电路的设计思想和实现方法，给出了我们所发明的电感耦合谐振回路的特性，对于内孔为100x100 μ〓的rf SQUID样品，用这种谐振回路和我们的读出电路，白噪声可测到15μ〓/√Hz左右，用1英寸的聚焦器可获得24fT／√Hz的磁场灵敏度。

PULL AWAY THE WOODEN BOLT PLUGS IN STERN TUBE FLANGE AND DRILL THE INSTALLATION HOLES.

6.2 拔出法兰面处的螺栓通孔中的木塞，钻孔并攻丝

Singer Leona Lewis and former Led Zeppelin guitarist Jimmy Page emerged as the bus transformed into a grass-covered carnival float, and the pair combined for a rendition of "Whole Lotta Love".

歌手leona刘易斯和前率领的飞艇的吉他手吉米页出现巴士转化为基层所涵盖的嘉年华花车，和一双合并为一移交&整个lotta爱&。

This is Kate, and that's Erin.

这是凯特，那个是爱朗。