英语人>网络例句>凹角 相关的搜索结果
网络例句

凹角

与 凹角 相关的网络例句 [注:此内容来源于网络,仅供参考]

Screw heads have to be polished, with their slots and rims chamfered.

所有螺丝帽的边缘及凹口都要削角抛光,螺丝尾则须做平面或球面抛光。

Home position shear tests of slope rock, point loading tests and indoor AMD simulation action tests in XingQiao concave slope had show shearing strength and coherence between body layers of quartz sandstone decrease by 13.2%~21.3% after attacked by AMD, the angle of internal friction between layers is decreased by 5.0%~7.5%, in general, AMD affects the rocks mechanical property at range of 60~100m interior the perpendicular slop. Data analysis shows: 1 The actions to slope are major focused on zone of weakness, shearing strength of slope foot and AMD centre are reduced by 52% and 64.7% separately. 2 The explosion stress wave of long distance field has obviously increasing influence to disturbance amplitude value of slope with increasing of the slope height and distance, the response of the top of slope and fault region are obvious as well as damage effect; the foot of slope is with smallest disturbance amplitude value, the disturbance amplitude value of the step close to free face is obviously bigger than the interior of slope. 3 With the coupling effect of the AMD and explosion loading, the stress distribution inside of slope mainly presents characters of explosion stress field; the area affected by AMD becomes a weak area of shearing stress.

新桥深凹露天矿边坡岩体的原位剪切试验、点载荷试验、室内模拟AMD作用试验表明:AMD蚀化后的石英砂岩,岩体层面间的抗剪强度和粘聚力减小的幅值约为13.2%~21.3%;层面间内摩擦角减小幅值在5.0%~7.5%之间;AMD一般影响垂直边坡体内部在60~100m范围内的岩体力学性质数值分析表明:AMD对边坡体的作用主要集中在弱化区域内,边坡体的底脚和AMD作用中心区域的剪切应力减少了52.0%和64.7%;(2)随着边坡体高度和距离的增加,远场爆炸应力波对边坡扰动幅值的增加趋势明显,边坡顶部和断层部位的响应突出,损伤效应明显;边坡底脚扰动幅值最小,临空面附近台阶的扰动幅值明显大于边坡体内部;(3)AMD与爆破荷载耦合作用后,边坡体内部的应力分布主要呈现出爆炸应力场的特征,AMD影响区域形成了一个剪切应力弱区。

Stem strongly grooved, puberulent on angles otherwise glabrous with scattered glands; leaves broadly ovate to ovate-orbicular, apex acuminate, margin coarse serrate or double serrate, apical tooth acuminate; corolla white

茎强烈具凹槽,被微柔毛的在角上或无毛具星散的腺体;重锯齿的叶宽卵形到卵形圆形,先端渐尖,边缘粗糙有锯齿或,渐尖的顶端齿;花冠白色 72 Isodon weisiensis 维西香茶菜

In most cases, this bearing outer ring A41C Type Pound-Grade Low Lift Spring Loaded Safety Valve locking mouth, and can not seal the resulting circular groove, leading many to be used in machine tool WA41C blanced bellows spring loaded safety valve spindle angular contact ball bearings can not be used as another host on the other bearings as filling grease.

大多数情况下,这种轴承的外圈带锁口,因而无法密封由此形成的环形凹槽,使得许多用在机床主轴上的角接触球轴承不能象用于别的主机上的其他轴承那样加注润滑脂。

Carving gravure of business card printing and membership card making production and offset business card printing and membership card making, and so on are very different, first of all the manuscripts submitted to approx 10 times, the perimeter line by hand is decisived on top of a piece of zinc tablet with a smaller machine to get an outside line back into the original large carved in a piece about an inch of eight brass, and copper strip it is some anticorrosive toppedwith films, because of copper strip is triggered from the perimeter line, so the rough body by hand for the film, when removed, and then use the medicine to the erosion of deep water, and proto-end knife with a magnifying glass and, thetolerant to the edge, sharp corners repaired, such as location on a layer of chrome, it's a printing plate.

雕刻凹版的制卡和会员卡制作制作与柯式制卡和会员卡制作等有很大的分别,首先把来稿放大约十倍,把外围线用手工刻划在一块锌片之上,再用一部缩细机械把外线缩回原大刻在一块约八份一寸的铜片上,而这件铜片上是涂有一些防腐蚀薄膜的,因为铜片只是勾上字的外围线,所以要用手工将粗身地上的薄膜刮去,然后用药水将印纹蚀深,最后仍要用放大镜及雕刻刀,耐性地将线边、尖角等位置修好,再镀上一层铬,这印版便大功告成。

第5/5页 首页 < 1 2 3 4 5
推荐网络例句

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时,他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了

The enrich the peopling of Deng Xiaoping of century great person thought, it is the main component in system of theory of Deng Xiaoping economy, it is a when our country economy builds basic task important facet.

世纪伟人邓小平的富民思想,是邓小平经济理论体系中的重要组成部分,是我国经济建设根本任务的一个重要方面。