英语人>网络例句>凹入 相关的搜索结果
网络例句

凹入

与 凹入 相关的网络例句 [注:此内容来源于网络,仅供参考]

The focusing effect by anyone of the biconcave erythrocyte, oblate spheroid,and disk sphere erythrocyte was found to be so remarkable that the light intensities at the focused areas close to the erythrocyte membrane were about 10 times higher than that of the incident light when the light irradiated along the erythrocyte plane.

我们发现会聚效应在双凹型,扁球体型或圆盘球体型红细胞中的任何一个都如此显著,以至于当激光照射方向沿着红细胞平面时在靠近红细胞膜的会聚区域的光强达到入射光强的10倍多。

Based on the method of numerical simulation, the diameter of steel billet, entrance half angle of concave die and the dimension of spline were analyzed for the forming force on the spline processing with the help of a rigid-plasticity finite element software Deform 3D.

借助刚塑性有限元软件Deform-3D,采用数值模拟的方法分析了矩形花键轴冷挤压过程中,坯料直径、凹模入模半角及键齿尺寸对花键成形力的影响。

A: The human eye is more sensitive to differences in some specific colors. For instance neutral grays, skin tones, chlorophyll greens and sky blues, so we choose these colors first. Then we choose saturated red, green, blue, cyan, magenta and yellow. After that we tried to fill the remaining big cavities in the color space.

答:人类眼睛对某些特殊颜色的差别较为敏感,例如中间灰色,皮肤调,叶绿素绿,天空蓝,我们预先选择了这些颜色然后饱和的红绿蓝洋红靛蓝和黄色,之后我们尝试填入色彩空间的剩余大凹处。

First of all, some structure parameters, such as the dimension scale of cavity walls, thelocation of primary flow injection holes, the entrance angle of main flow, and so on, havebeen studied, focusing on their influence to the cavity flow field, the forming of vortexes,and the pressure drop in the combustor.

首先研究了模型燃烧器中凹腔长度与前后壁面高度比例、腔内燃料与空气的入射位置、以及主流入射角度等结构参数对腔内流场变化、驻涡形成、以及燃烧器压损等方面性能的影响。

Two pairs of antennae very short, there is 1 on a stalk eyes, can shrink into the concave fossa.

触角2对,很短,有1对具柄的眼,能缩入凹窝内。

Previous literature has shown that when p-polarized wave impinging upon a corrugated metal thin film with a single slit, sharp peaks present on the transmission spectra at wavelengths much larger than the slit width.

先前曾有文献指出当p-极化的光波入射於一个具有单狭缝的属薄膜,并且在属表面制造凹槽阵,在透射的频谱上将会出现剧的峰值。

This kind of tangential distortion, rubber fabric is like a kind of enterokinesia myofascialcutaneous, the ultimate in Nano-imprint lithography appear on both ends of the interval size of nano-imprint lithography convex hull, with the time, rubberand enterokinesia of largening, resulting in business card printing and membership card product forward control appears on the line of symmetry.

这种切向变形,使橡皮布暗地有如一种蠢动状,首先在不抬印区间的两头不入现不小小不等的凹包,随着不抬印工夫的放不小,橡皮蠢动量加不小,从而造不败在制卡和会员卡制作产物上不入现周向后规线不不差称不到位的本体。

A maths model according to anatomic measure in Transorbital Roof Craniotomy were established to compare with transorbital keyhole approach to frontal base meningioma and pituitary adenoma. We discovered that removing 1cm orbital roof bone will increase the instrument handle angle from 360 to 450(25%).

本文通过经眉弓锁孔去眶顶入路对前颅凹底脑膜瘤垂体瘤的手术治疗,从解剖测量数据建立几何数学模型,与传统眉弓入路进行比较发现去除1cm的眶顶骨质,在理论上手术器械的操作角度从360增加到450即增加25%。

In the middle of a blow, then deep, because under the surface pulp cavity, so hypertrophy, fragrant like a circle after circle, but it tastes, flaky, crisp, Soft three mixed feelings.

炸时用的铁勺子,直径约5寸,四周下凹,中央凸起,用另一勺将那种混合浆舀入面窝勺,在中间一刮,然后下锅,下凹处因面浆多,所以肥厚,炸成后像个圆圈圈,吃在嘴里,酥、脆、软三种感觉混合。

The advanced method is to use a new type of bearings are embedded in the seal groove, the groove depth than the standard bearings are slightly A42C Type Pound-Grade Low Lift Spring Loaded Safety Valve shallow point, and just fit in the intersection part, fill in the gap left by the outer ring flange.

该先进方法是用一新型有凹槽的密封圈嵌入轴承中,该凹槽深度要比标准轴承的稍浅点,且恰好适配于相交部分,填入外圈凸缘留下的间隙。

第4/5页 首页 < 1 2 3 4 5 > 尾页
推荐网络例句

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应,而且减少跟风的可能性。

The new PS20 solar power tower collected sunlight through mirrors known as "heliostats" to produce steam that is converted into electricity by a turbine in Sanlucar la Mayor, Spain, Wednesday.

聚光:照片上是建在西班牙桑路卡拉马尤城的一座新型PS20塔式太阳能电站。被称为&日光反射装置&的镜子将太阳光反射到主塔,然后用聚集的热量产生蒸汽进而通过涡轮机转化为电力