凸缘

Cilia of ocrea 0.5-5 mm; achenes biconvex, rarely trigonous.

托叶鞘的缘毛0.5-5毫米；瘦果两面凸，很少三棱。

Results Mucopolysaccharidosis typeⅠ had characteristic X-ray changes of bones:①Enlarged skull and hook- shape Sella Turcica;②Short and thick phalanges and metacarpal Bones;③Dilated central part and thin ends of upper and lower limb bones;④Kyphosis deformity of spine, beak-shape stick out of anteroinferior margin of Kyphosis deformity vertebra;⑤Broadening ribs as paddle shape;⑥Shallow acetabulum and enlarged Acetabular Angle;⑦Prolonged femoral neck, Coxa Vara or coxa valga.

结果 粘多糖病Ⅰ型具有较典型的骨骼X线改变，(1)头大，蝶鞍呈乙型；(2)掌指骨粗短；(3)上、下肢骨中央膨胀两端变细；(4)脊椎后凸成角，后凸椎体前下缘成鸟嘴状突出，上下椎体呈卵圆形；(5)肋骨增宽呈船桨；(6)髋臼变浅，髋臼角增大；(7)股骨颈增长，髋内翻或外翻。

Methods Respectively analyzed the X-ray, CT and image post-processing manifestations of mucopolysaccharidosis type Ⅰ. Results Mucopolysaccharidosis typeⅠ had characteristic X-ray changes of bones:①Enlarged skull and hook- shape Sella Turcica;②Short and thick phalanges and metacarpal Bones;③Dilated central part and thin ends of upper and lower limb bones;④Kyphosis deformity of spine, beak-shape stick out of anteroinferior margin of Kyphosis deformity vertebra;⑤Broadening ribs as paddle shape;⑥Shallow acetabulum and enlarged Acetabular Angle;⑦Prolonged femoral neck, Coxa Vara or coxa valga.

结果 粘多糖病Ⅰ型具有较典型的骨骼X线改变，(1)头大，蝶鞍呈乙型；(2)掌指骨粗短；(3)上、下肢骨中央膨胀两端变细；(4)脊椎后凸成角，后凸椎体前下缘成鸟嘴状突出，上下椎体呈卵圆形；(5)肋骨增宽呈船桨；(6)髋臼变浅，髋臼角增大；(7)股骨颈增长，髋内翻或外翻。

The units can also be specified with bore diameters of between 30 and 60mm and can be supplied as a plummer block assembly or with square or oval flanges, making them an extremely versatile solution.

这些单位也可以指定承担直径为30至60毫米，可提供作为座组装或方形或椭圆形凸缘，使他们一个极其灵活的解决方案。

The units can also be specified with bore diameters of between 30 and 60mm and can be supplied as a Plummer block assembly or with square or oval flanges, making them an extremely versatile solution.

这些单位也可以指定承担直径为30至60毫米，可提供作为立式装配或方形或椭圆形凸缘，使他们一个极其灵活的解决方案。

The stripper may also be used to form slight indentations or re-entrant curves in the botton of a cup, with or without a flange.

脱衣舞娘也可以用来形成轻微凹入或重入曲线在底部的杯，或无凸缘。

In the bearing ring or a bearing wall or a flange gasket for ease of grinding the roots of the open trench or slot.

在轴承套圈或轴承垫圈的挡边或凸缘根部为便于磨削所开的沟或槽。

The pump pulley and the transmission gearbox shell is united as one body, fixes behind the engine crank on the flange.

泵轮与变速器壳体连成一体，固定于发动机曲轴后端的凸缘上。

The advanced method is to use a new type of bearings are embedded in the seal groove, the groove depth than the standard bearings are slightly A42C Type Pound-Grade Low Lift Spring Loaded Safety Valve shallow point, and just fit in the intersection part, fill in the gap left by the outer ring flange.

该先进方法是用一新型有凹槽的密封圈嵌入轴承中，该凹槽深度要比标准轴承的稍浅点，且恰好适配于相交部分，填入外圈凸缘留下的间隙。

The forming process and the characteristics of plastic deformation, the sites of the heavily strained zones with severe thickness reduction and their evolution, the influences of the main processing parameters, such as the plastic melt pressure and its distribution from the gate to the end of the mold, and of friction coefficient between the sheet flange and the mold, on these during the hybrid forming of the aluminum sheet have been revealed by the updated Lagrange finite element formulation for the finite elastic-plastic deformation.

运用弹塑性大变形更新的Lagrange有限元方法，揭示了铝薄板的成形过程和塑性变形的特点与规律、大塑性变形区的产生位置及其塑性变形特点，探明了复合成型过程中塑料熔体压力及其分布规律以及铝薄板凸缘与模具摩擦系数等主要工艺参数对铝薄板成形过程和塑性变形的影响规律。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。