几何形状

The two fractal parameters (amplitude B and fractal dimension D) in the new model represent the roughness of primary and higher order asperities of stationary profiles, respectively.

接着在节理表面形状的精确测定基础上，根据分形理论的变量图法，建立了描述岩石节理表面几何形状的新的分形模型。

Then, by grace He continues to use life's twists and turns to reshape us into more Christlike persons,"conformed to the image of His Son" Rom.

在摺纸时，将纸张按不同的几何形状摺叠起来，就变成了一只鸟或是其他特别的形状。

The geometrical morphology of Radiolaria reflects the potential provided by the mega-printer, able to build any complex geometry without the use of provisional, temporary formwork or disposable, expensive moulds.

几何形态的放射虫反映所提供的潜在的大型打印机，能够建立任何复杂的几何形状，而无需使用临时的，暂时的模板或一次性的，昂贵的模具。

When the skeleton deforms your geometry as much as it does here, it is very important that the geometry is in the exact same position it was before you bound it when you go to create your morph targets.

当你的骨骼变形尽可能它在这里，这是非常重要的几何形状完全相同的立场，这是它之前，你一定当你去创建自己的目标是几何变形。

The typified programming technique for numerical control, described in this paper, is established on the basis of characteristic analysis of geometric configurations and dimensions of any two-dimensional patterns.

本文提出的数控编程典型化技术，是在对任意二维空间图形的几何形状及几何量进行特征分析的基础上建立起来的。

Taking into account the influences of scatterer geometrical shapes on induced currents, an algorithm, termed the sparse-matrix method, is proposed to calculate radar cross section of aircraft configuration.

论证了散射体几何形状对感应电流的影响规律，并基于飞行器几何外形特征和矩量法，提出了一种用于飞行器雷达散射截面计算的高精度快速算法。

The monotony and extremum theory of function are applied to prove the geometrical characteristic of error hand for 2D linear segment uncertainty ε(subscript σ) model in theory. The result shows that the error hand has the geometrical shape of "larger ends and smaller middle" or "one end larger and the other smaller". The minimum width and its exact position of the error hand are calculated too. It is proved that the minimum width position of the error hand is near the end with the smaller mean square error.

运用函数单调性和极值理论，从理论上证明ε模型的误差带的几何特征；得到线元误差带不仅具有&两端大、中同小&，而且也可能具有&一端大、一端小&的几何形状；给出了误差带的最小带宽及其位置；论证了误差带的最小误差带宽的位置靠近中误差较小的一端。

Based on the 3D solid model, the changing trend of spiral angle and pressure angle of pitch cone, the thickness-changing trend of face and pitch cone can be analyzed. In addition, the method of cutting tooth on general NC machining center and the measurement of tooth flank geometry on 3D CMM are conducted.

根据锥齿轮切齿仿真所获得的三维几何模型，本文还研究了在通用四轴联动加工中心上加工锥齿轮齿形的方法和在通用三坐标测量机上进行锥齿轮齿面几何形状误差测量及数据处理方法。

In this paper, a new method is presented to overcome this problem. By matching the 3D points reconstructed from the images and the known geometric model in space, the topology and curvature information of the model surface can be fully utilized and all the images to the 3D model stitched at the same time.

提出了一种新的配准方法来解决这一问题，由于采用了基于图像重建的采样点模型与已知几何模型在空间中匹配的方法实现配准，因而充分利用了物体几何形状本身的拓扑和曲率等信息，并可以一次性地实现所有图像与空间物体的配准。

To obtain more uniform temperature distribution and relative lowest temperature over cross section of the rotor, on the basis of test data of a given example of a 150MW turbo generator with air coolant, numerical solution of two dimensional modelling equations of air turbulent flow and heat transfer in and between cooling duct and rotor were carried by the Finite Volume Method at condition of varying configuration parameters of sub slot, the number of winding's cooling ducts and center distance of them, and the diameter of slot wedge.

为了能够得到转子截面较均匀并且最高温度值较低的优化温度分布，文中在150MW空冷汽轮发电机转子实验研究基础上，改变副槽的几何形状、径向通风沟的条数及间距、槽楔出风口直径等几何量，采用有限体积法求解转子本体及通风道内空气的传热及紊流流动等二维离散方程组。

The labia have now been sutured together almost completely.The drains and the Foley catheter come out at the top.

此刻阴唇已经几乎完全的缝在一起了，排除多余淤血体液的管子和Foley导管从顶端冒出来。

To get the business done, I suggest we split the difference in price.

为了做成这笔生意，我建议我们在价格上大家各让一半。