凝固

Methods We performed animal studies in vitro and in vivo by using uMC-I Ultrasound-guided Microwave Coagulation Equipment percutaneously.

采用UMC-I型超声引导微波凝固治疗仪进行离体及活体肝实验。

The most common microbes causing infections in percutaneously inserted uncuffed catheters are, in order of prevalence, coagulase-negative staphylococci, Staphylococcus aureus, Candida species, and enteric gram-negative bacilli.

根据患病率的高低，引起经皮插入的无气囊导管感染的最常见的微生物排序如下：凝固酶阴性葡萄球菌、金黄色葡萄球菌、念珠菌属菌种和肠道革兰氏阴性细菌。

Developments of both theoretical and experimental results of low velocity coupled growth and banded structure of peritectic alloy are reviewed.

综述了包晶合金定向凝固中的低速带状与共生生长组织的实验和理论研究情况及其进展。

The effect of high intensity ultrasonic on solidification process of Sn Sb peritectic alloy was investigated.

在锡锑包晶合金的凝固过程中导入高能超声，不仅显著细化α相和β相晶粒组织，同时使具有立方晶体特征的β相组织有明显的球化趋势，消除了密度偏析。

Cu peritectic alloy has been unidirectionally solidified with a wide range of growth velocities.

37％Cu包晶合金的凝固过程及其组织形态。

Formation Mechanism of Band Structure and Phase Selection During Directional Solidification of Peritectic Alloys II.

定向凝固包晶合金带状组织的形成机制及相选择 II。

The effect of segregation of elements on the structure ofsemikilled low alloy steel ingot, taking into consideration the peritectic reaction.

枝晶凝固过程中元素对半镇静钢钢锭结构的影响。由此选择冶炼控制成份。

Unidirectional solidification experiment on Zn-2%Cu peritectic alloy was carried out by Bridgman method. Lamellar structure was obtained at a solidification velocity between 1600μm/s and 6400μm/s.

摘 要：利用Bridgman法对Zn-2%Cu包晶合金进行了快速定向凝固实验研究，当生长速度在1600～6400μm/s时，得到了类似于共晶的层片状组织。

The structure was investigated by XRD and TEM, combining with the calculated metastable phase diagram. The results show that it is possible to obtain coupled structure in Zn-2%Cu peritectic alloy by rapidly unidirectional solidification method.

利用X射线衍射仪及透射电镜对层片状组织进行了相组成的分析，并结合计算亚稳相图对该组织的相及组织形成规律进行了分析，结果表明在快速凝固条件下Zn-2%Cu包晶合金中实现共生生长是可能的。

Reparation of PBO was begun with the polymerization process in which composite salts that contained 4,6-diaminoresorcinol and terephthalic acid were dissolved in polyphosphoric acid and phosphorus pentoxide.

BO纤维制备：以4，6-二氨基间苯二酚的盐酸盐为单体原料，与对苯二甲酸混合，经过中和反应、脱色处理、干燥后制成复合盐；再以多聚磷酸为溶剂，添加五氧化二磷和抗氧化剂，经过预聚合反应制备出PBO聚合物；聚合物通过双螺杆挤出机进一步进行聚合，然后通过喷丝板挤出，在磷酸水溶液中凝固成型，经过洗涤、干燥等过程，最终卷绕成型。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。