减速

The output rotating speed is generally 65-110r/min with adopting the upright cycloidal pin-wheel decelerator.

一般输出转速65-110r/min。用 XLD 型立式摆线针轮减速机。

Remove the two screws and washers, Items 102 and 105, securing the spacer Item 88 to the body Item 50 Remove the body item 50 Using a strap pipe wrench, turn stud Item 11 while keeping the drive shaft stationary in order to release the shafting Item 20/11 from the reduction gear's output shaft.

删除这两个螺丝和垫圈，项目102和105 ，确保项目88间隔的机构项目50 删除机构项目50 使用带管扳手，反过来螺柱项目11 ，同时保持平稳的传动轴，以便释放轴系项目20/11从减速机的输出轴。

The engage gears noise analysis of the planet cycloidal needle wheel decelerator showed that manufacturing errors of key positions of spare parts such as cycloidal wheel,needle wheel,output shaft and lack impartiality set etc.

通过对行星摆线针轮减速机轮齿啮合噪声分析，表明摆线轮、针轮、输出轴和偏心套等零件关键部位的制造误差是产生噪声的主要原因，从工艺角度提出提高零件制造精度和专用胎具精度降低噪声的方法。

This design firstly fixed ondesign scheme and selected basic components, and besides, developedthe reliability analysis of transmission system. The design ofMG300/701-WD Shearer's cutting unit. It is made up of a gearbox andmoderate breeze gear wheel transmission that the MG300/701-WD typemining machine cuts the cutting department, Cut the electricalmachinery of cutting department and put to fix up horizontally inthe rocker arm, The power that the motor outputs leans on a roundof transmission of department of gear wheel and planet round viathe tertiary straight tooth, Urge the cylinder to rotate finally.

本文首先确定了设计方案和选择了基本部件并开展了传动系统的可靠性分析，MG300/701-WD型采煤机截割部主要是由一个减速箱和四级齿轮传动组成，截割部电机放在摇臂内横向布置，电动机输出的动力经由三级直齿圆拄齿轮和行星轮系的传动，最后驱动滚筒旋转。

Use: Dispels all Fear, Polymorph and Slowing effects.

使用：消除所有恐惧、变形和减速效果。

The roller furnace pot uses the 1Cr18Ni9Ti stainless steeliness circled to columnar, or uses the chromium manganese nitrogen refractory steel casting, one side bearing spider outside the furnace body supporting, and uses the electric motor belt speedreducer to carry on the passing-use, to cause the furnace pot to revolve slowly, the work piece causes it heating along with drum furnace pot revolving evenly, and work piece mutually between non-cover phenomenon, after heat treatment, the luster is consistent, furnace pot another end is a feeding head,by two trolley supporting.

滚筒炉罐采用1Cr18Ni9Ti不锈钢制成圆柱型，或采用铬锰氮耐热钢铸件，一端由轴承支座在炉体外支承，并采用电动机带减速机进行传用，使炉罐缓慢旋转，工件随滚筒炉罐旋转使之受热均匀，并且工件互相之间无复盖现象，热处理后色泽一致，炉罐另一端为进料口，由二只滚轮支承。

The reduction gearbox of heavy mill is key to powder mill ing.

大型磨机齿轮减速箱是粉磨生产过程的重要设备。

MCU control motor acceleration and deceleration of the language, more practical control unit.

详细说明：51单片机控制电机加减速的语言，比较实用的控制单元。

They mainly are applicable to a tool machine principal axis, car clutch and decelerate machine etc..

它们主要适用于机床主轴、汽车离合器、减速机等。

Compared with similar advanced equipment, FPP Series mill has advantages as follows,① Adding the cutting and grinding function;② Extend the time of material pressing and cutting and grinding;③ Solve the sensitivity of keeping the proportional spacing and proportional thickness;④ Widened material input size;⑤ Material output size are in a perpetual state;⑥ Multifunctional machine is used to dry and grind and filtrate material;⑦ Auxiliary equipment is less and covering is small and investment is small;⑧ Noise is low and dust is small, it is beneficial to protect environment and keep physical and mental health for operation workers.

FPP 型系列磨机的结构形式是电机拖动减速机带动磨盘旋转，带有压力的磨辊在磨盘上自转，对物料进行碾压，磨内的物料在旋转离心力的作用下均匀进入碾磨区，磨辊对物料实施挤压、剪切、研磨，故破碎能力大，粉磨能力强，与同类先进设备相比：①增加了剪切研磨功能；②延长了物料挤压剪切研磨时间；③解决了对物料粉层均匀一致，厚度一致的过于敏感性；④拓宽了对物料的进料粒度；⑤物料的出料粒度永远处于受控状态；⑥可以对物料进行烘干、粉磨、筛分一机多能化；⑦辅机设备少、占地小、投资省；⑧噪音小、扬尘点少，有利于环保和操作工人的身心健康。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。