冷却的

As such, the insulation was designed to accomplish this through combined ablative cooling and thermal resistance.

因此，保温的目的是要做到这一点，通过联合烧蚀冷却和热电阻。

Deformation greatly promoted carbonitride isothermal precipitation and made C-curve shift leftwards. The position and shape of C-curve depended on the content of Nb and N to a great extent, C-curve shifted leftwards a little when N content increased and its nose temperature was raised with Nb content increased. 3 when cooling rate increased, start temperature and finish temperature of continuous cooling precipitation decreased, full precipitation became difficult to take place, the volume fraction of carbonitride precipitation decreased, molar fraction of Nb and C dissolved in austenite increased, and the precipitation grain was further refined. Deformation shorten precipitation start time during continuous cooling, raised precipitation start temperature, accelerated precipitation kinetics of carbonitrides.

计算表明：1在Fe—Nb—C系统中，随着温度的降低，析出相的平衡体积分数增加，溶解在奥氏体中的Nb、C的摩尔分数降低，析出相中C和Nb的原子分数的比值v增加；2变形大大促进了碳氮化物的等温析出，使C曲线左移，Nb和N的含量与C曲线的位置和形状有一定的关系，N含量的增加，使C曲线略有左移，而Nb的含量的增加使得C曲线的鼻子区上移；3随着冷却速率的增大，连续冷却析出的开始温度和结束温度均有所降低，并且析出变得越来越不充分，析出相体积分数明显减小，溶解在奥氏体中Nb和C的摩尔分数增大，析出相粒子被明显细化，变形大大缩短了CCP过程碳氮化物析出的开始时间，提高了析出的开始温度，促进了析出动力学。

In this paper, the 3-D finite element relocating mesh method is used to calculate the temperature field and the thermal creep stress field of spillway dam and mid level outlet dam in certain roller compacted concrete gravity dam, sensitivity analysis have been down with different parameters, such as placing temperature, the location of cooling pipe, cooling temperature, time for water supply, ascended-layer of concrete, intermissive time and different placing time, and the commendatory construction scheme have been put forward in such analysis; according by the test result on the two scheme of concrete aggregate combination (basalt as coarse aggregate and limestone as fine aggregate, basalt as coarse aggregate and basalt as fine aggregate), simulation analysis on temperature field and thermal creep stress field of the commendatory construction scheme have been down, and analysis have also been down on temperature field and thermal stress field of the two different aggregate combination, the result indicates that the spillway dam and mid level outlet dam which adopted these two aggregate combination can both satisfy the require of design crack resistance in concrete, furthermore limestone as fine is better than basalt as fine aggregate; the effect of summer water storage and winter water storage on the temperature field and thermal stress field have been analyzed, comparing with winter water storage, in summer water storage scheme the maximum tensile stress at abnormal concrete in upstream fill is decreased by 0.1～0.3MPa and there are no evidence change of the maximum tensile stress at other parts, which indicate that summer water storage is avail for the crack resistance of upstream fill; according to the simulation calculating result and comparing temperature simulation calculating results and temperature controlling measures of some similarity projects both completed and construction, synthesis appraise have been carried to the design temperature controlling measures of dam, and the temperature controlling measures of this project have been brought forward, all these have great reference value on the design of temperature controlling measures and the optimization of the construction scheme.

本文采用三维有限元浮动网格法仿真计算程序，对某碾压混凝土重力坝的溢流坝段和中孔坝段分别进行了三维有限元温度场和温度徐变应力仿真计算分析，对浇筑温度、冷却水管的布置方式、冷却水温、通水时间、浇筑升程和间歇时间、不同开始浇筑日期等参数进行了敏感性分析，在此基础上提出了推荐的施工方案；根据两种骨料方案(玄武岩粗骨料+灰岩细骨料方案；玄武岩粗骨料+玄武岩细骨料方案)的混凝土性能试验研究成果，对推荐的施工方案进行了温度场和温度徐变应力仿真计算，并对比分析了两种不同骨料情况下的温度场和温度应力，结果表明溢流坝段及中孔坝段采用上述两种骨料均能满足混凝土的抗裂设计要求，且灰岩细骨料优于玄武岩细骨料；计算分析了夏季蓄水和冬季蓄水对坝体温度场和温度应力的影响，夏季蓄水方案与冬季蓄水方案相比，坝体上游变态混凝土区域最大拉应力小0.1～0.3MPa，其他部位最大拉应力无明显变化，夏季蓄水对坝体上游面混凝土的抗裂有利；根据仿真计算成果并通过比较国内一些已建和在建的类似工程的温度仿真计算成果及采取的温控措施，对大坝的设计温控措施进行了综合评价，并提出了该工程的温控措施，对温控设计和优化施工方案具有重要参考价值。

No entire nitrendipine crystals were observed visually in SEM photos. The results of X-ray diffraction and differential scanning calorimetry analysis indicated that the crystalline form of nitrendipine was highly dispersed in microspheres, so as amorphous state. The drug release rate of microspheres could be controlled with adjusting the ratio of solid dispersion carriers and retarding agents formulated. The agitation speed and temperature of the preparation process have distinct effect on micromeritic properties of microspheres. The release profiles of the microspheres were mainly affected by the stirring rate of paddle, the concentration of SDS and pH of dissolution medium. Cooling speed and time, however, have no evident influence on the drug release rate of the microspheres. The dissolution data showed that the mechanism of drug release from microsphers was mainly diffusion-controlled. The incorporation efficiencies of 3 batches sample were exceed 96. 8％, which implied that the current method was suitable for design sustained-release dosage form for poorly water-soluble drug.

在扫描电子显微镜下观察，在微球内外未发现尼群地平的完整结晶，X-射线粉末衍射和差示扫描量热试验结果也显示，尼群地平已经被高度分散在微球中；微球的释药速度可通过调整处方中固体分散体载体和阻滞剂的比例控制；制备温度和搅拌速度对微球的质量影响较大；溶出仪的搅拌速度，释放介质的浓度和pH对微球的释放有较大的影响；制备过程中的冷却速度和冷却时间对微球的释放行为影响不很明显；方程拟合的结果表明缓释微球的释药行为符合扩散机制；测定三批微球样品的包封率均在96.8％以上，表明该法适合于制备难溶性药物的缓释微球。

First according to the hydraulic pressure elevator system diagram, use the machine design and hydraulic transmission knowledge calculates the diameter of the plunger, cylinder tube wall thickness as well as cylinder bottom thickness; second, through the examination confirmation to the obtained result to complete the work of cylinder design; Simultaneously has carried on the component choice and the computation; Through to the system calorific capacity computation the and the volume of cooling water while the fuel tank cools when needs to complete the hydraulic pressure elevator fuel tank design; Based on the system oil stream condition to calculated the tube internal pressure lose, the local pressure loss as well as the all of the pressure lose to carried on the system checking calculation; Finally through the consult correlation design handbook to calculation and examines the belt, the band pulley, the axis, as well as the key, has completed the hydraulic pressure elevator pumping station transmission system design.

首先根据液压电梯系统原理图，利用机械设计与液压传动等方面的知识计算出柱塞的直径、缸筒的壁厚以及缸底厚度，并对所得结果进行校核验证完成了工作油缸的设计；同时进行了元件的选择和计算；其次，通过系统发热量的计算和油箱冷却时需要的冷却水量的计算完成了液压电梯油箱的设计；依据系统油流状态计算出管内压力损失、局部压力损失以及总压力损失进行了系统的验算；最后通过查阅相关设计手册对带、带轮、轴、以及键进行设计计算和校核，完成了液压电梯的泵站传动系统的设计。

Firstaccording to the hydraulic pressure elevator system diagram, usethe machine design and hydraulic transmission knowledge calculatesthe diameter of the plunger, cylinder tube wall thickness as wellas cylinder bottom thickness; second, through the examinationconfirmation to the obtained result to complete the work ofcylinder design; Simultaneously has carried on the component choiceand the computation; Through to the system calorific capacitycomputation the and the volume of cooling water while the fuel tankcools when needs to complete the hydraulic pressure elevator fueltank design; Based on the system oil stream condition to calculatedthe tube internal pressure lose, the local pressure loss as well asthe all ofthe pressure lose to carried on the system checking calculation;Finally through the consult correlation design handbook tocalculation and examines the belt, the band pulley, the axis, aswell as the key, has completed the hydraulic pressure elevatorpumping station transmission system design.

首先根据液压电梯系统原理图，利用机械设计与液压传动等方面的知识计算出柱塞的直径、缸筒的壁厚以及缸底厚度，并对所得结果进行校核验证完成了工作油缸的设计；同时进行了元件的选择和计算；其次，通过系统发热量的计算和油箱冷却时需要的冷却水量的计算完成了液压电梯油箱的设计；依据系统油流状态计算出管内压力损失、局部压力损失以及总压力损失进行了系统的验算；最后通过查阅相关设计手册对带、带轮、轴、以及键进行设计计算和校核，完成了液压电梯的泵站传动系统的设计。

This paper using the FEM software Marc, for the 50 and 60 degree V groove of flat plate butt joint simulate the one-layer and three layers welding, finish each welding and cooling it down to room-temperature then start the next welding true represent process and get the temperature field, residual deformation and welding residual stress, according to the theory analysis and empirical equation verified the temperature field and residual deformation all correct, comparison with experiment verified the welding residual stress regularity and correctly.

本文利用有限元软件Marc，对开60°和50°V型坡口的平板对接接头，动态的模拟了单层单道打底焊，焊完一道后让试件冷却到室温以及单层单道满焊，每焊完一道后让试件冷却，然后再焊下一焊道，道间温度≤200℃，在以此为初始边界条件下开始下一道的焊接，真实的再现了焊接过程，得出了温度场，残余变形和残余应力场的分布规律，根据理论分析及经验公式验证了温度场以及残余变形的正确性，角变形的大小，这些结果与数值计算相吻合。通过与实验测得的残余应力进行比较，验证了焊接残余应力的分布规律及模拟的正确性。

This invention relates to a method and device for generating cold atomic beam. Said method includes heating hot atom source in vacuum chamber to form atomic saturated vapor pressure atmosphere, cooling hot atom by three-D MOT to below 200uk and trapped to form cold atomic cloud, by the quarter wave plate reflection mirror in MOT the laser radiation pressure being unbalanced to make cold atom emitting along said direction, four tape arranged straight line set with contrary current direction is set in atom beam emission direction, which makes the atom emitted to forward to obtain cold atom beam with low speed, large flux and small transverse speed, laser beam vertical with atom beam set in the direction of cold atom emitting for atom beam state preparation to realize state concordant emitted cold atom beam.

本发明涉及一种冷原子束产生方法和装置，该方法包括在抽真空的真空室内，加热热原子源，在真空室中形成相应的原子饱和蒸汽压气氛；采用三维MOT对热原子进行冷却，冷却到200μk以下，并被捕获形成冷原子云团；通过三维MOT中开小孔的四分之一波片反射镜，而使得在该方向上激光辐射压力不平衡，使冷原子沿此方向出射；在冷原子束出射方向上，还置有载有彼此电流方向相反的四根成锥形排列的直导线，从而原子出射时将在磁场的作用下，不会沿横向膨胀而向前射出；便得到了出射速度低的、通量较大的、横向速度非常小的连续冷原子束；同时在冷原子束的出射方向上，设置有与原子束垂直的激光束，用于原子束的态制备，实现态一致的出射冷原子束。

The influence rule to powder quality and quantity from some technical parameters such as materials vapor tension, gas pressure, the ratio between hydrogen and argon, current intensity and gas circulate intensity were discussed by single-factor experiment, on the base of which the perpendicularity experiment scheme was arranged.

本文采用压力模型计算出稳定弧光制粉时的气相空间温度在373K以下；从电流密度和电导率角度计算出等离子体电弧场中心温度高达5000-6500K；由此得出弱电离等离子体自由弧的自身温度场即使没有外界强制冷却，在等离子体焰区特征半径(约1.26cm)范围内的温度梯度就可达4787℃/cm，这是电弧等离子体温度场分布高度集中的具体表现，也是纳米金属粉末无须液氮冷却就能生成的本质原因，阐释了等离子体温度场自身的极大温度梯度是金属粉体纳米化的控制机制。

A method for making Bisphenol A with a purity of more than 99.7% by reacting phenol and acetone using an acid catalyst, separating a BPA-phenol adduct by crystallisation and removing phenol from the adduct, in which involves continuous suspension crystallisation with a total dwell time of more than 4 hours in at least 3 crystallisers, by cooling first to 50-70 C in two parallel crystallisers and then to 40-50 C in a third crystalliser connected in series with the first two.; A method for the production of Bisphenol A with a purity of more than 99.7%, by reacting phenol with acetone in presence of an acid catalyst, separating a BPA-phenol adduct from the product mixture by crystallisation, filtration and washing, and removing the phenol from the adduct, in which stage involves continuous suspension crystallisation in at least three crystallisers connected in such a way that the mixture is first cooled to 50-70 C in two crystallisers in parallel and then cooled to 40-50 C in a third crystalliser in series with the first two, the total residence time of the mixture over all crystallisers being more than 4 hours.

描述用于生产纯度大于99.7％的双酚例如，双酚A(BPA的方法，这种方法包含苯酚和丙酮在有酸性催化剂参与的情况下反应形成一个包含双酚的产物混合物；通过结晶、过滤和洗涤从该产物混合物中以双酚/苯酚复合物的形式除去至少一部分双酚以提供双酚A/苯酚复合物晶体；并且从双酚/苯酚复合物晶体中除去至少一部分的苯酚以提供纯度大于99.7％的双酚；其中结晶过程包括连续的混悬液结晶，并且是在至少三个结晶装置中进行的，装置的排列使得产物混合物首先在结晶过程的第一阶段在第一个结晶装置和并联的第二个结晶装置中被冷却到50至70℃的温度，随后在结晶过程的第二阶段在与第一和第二个结晶装置下游串联的第三个结晶装置中被冷却到40至50℃的温度，并且其中产物混合物在结晶过程中的总驻留时间在4小时以上。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。