冷却的

The result shows that the flavors of oils and fats has a lot of differences,the cooled way of the deodorized oils is a key factor for flavor of oils and fats.

分析油脂脱臭工艺和设备，脱臭油脂的冷却方式是影响成品油风味的关键因素，确定脱臭油应在真空和水蒸汽汽提的状态下冷却到 1 90℃以下。

It use two disparting surface,and its frame is fast.It use point moulding gob,so,it can fall off automatism.When it is pulled out ,the pulling pole pull the product and accomplish the pulling of its side concave . The design project is divided into two parts. The first part is about the working theory and application of a plastic injection mould, the principle of designing and the introduction of the production about plastic mould.

它采用双分型面分型，结构紧凑；采用点浇口，且浇口可以自行脱落；顶出时，由推杆和斜顶杆顶出制品并完成制品内侧凹的抽芯；模具定模上的水道以多支回路分别冷却，动模一侧的型芯由三组水道分别冷却。

It use two disparting surface,and it's frame is fast.It use point moulding gob,so,it can fall off automatism.When it is pulled out ,the pulling pole pull the product and accomplish the pulling of it's side concave . The design project is divided into two parts.

它采用双分型面分型，结构紧凑；采用点浇口，且浇口可以自行脱落；顶出时，由推杆和斜顶杆顶出制品并完成制品内侧凹的抽芯；模具定模上的水道以多支回路分别冷却，动模一侧的型芯由三组水道分别冷却。

Additionally, the air cooling zone should be set up so as to cool the steam and air mixture. Thus, the steam and air mixture supercooling can be enlarged, the working medium loss reduced and the burden of air ejector taken away.

另外，应该设置空气冷却区，使蒸汽-空气混合物得到冷却，以增大排出的蒸汽-空气混合物的过冷度，减少工质损失，并降低抽气器的负荷。

When evaporative cooling hydrogenerator ( generator/ motor) runs with a certain load, all bars of stator windings change under the same law : Temperature of bar increases arising from winding loss, and temperature of cooling medium in hollow conductor of bar is also increased through specific heat capacity, and it comes to boiling and is boiled away partially when temperature reaches a saturation that required by corresponding pressure.

当蒸发冷却水轮发电机以某一负载运行时，定子绕组所有线棒发生着同一规律的变化：铜损耗使线棒发热，线棒空心导体中的冷却介质通过比热容吸热使温度线性上升；当温度达到压力所对应的饱和温度时便以蒸发潜热吸热而部分沸腾汽化。

For example, in cases where the target temperature is 60° C., the fan revolution speed, which is shown by a two-dot chain line, does not rise immediately when the actual temperature of the cooling target fluid exceeds the target temperature of 60° C.

例如，在的情况下，目标温度为60 ° C时，风扇转速，这是表现出两个斑点链路线，并没有立即上升时，实际温度的冷却液指标超过目标温度为60 ℃之间，但后，冷却液的目标，极大地overshoots目标温度。

In order to acquire the thermalcontraction value of the plate during cooling and offer the proper value for modifyingmold,The rule of thermal contraction have to be analyzed during cooling.

为了得出中厚钢板弯曲件在冷却过程中所产生的收缩量，为模具修正提供合理的修模数据，有必要分析其在冷却过程中收缩的规律。

After cooling catalyst to 52℃, all the diesel cooling oil remaining in the drum is drained back to the diesel oil surge drum through the screen cone, provided at the bottom of the vessels.

经过冷却催化剂的温度降到52℃，所有罐底留存的冷却柴油经过锥型过滤器过滤后排放到位于容器底部的柴油缓冲罐。

The third section was on the change of beef tenderness during the preservation. It is the first time that the variation of tenderness and the change of pH were studied. Results showed that Warner-Bratzler shear force, which is denotating the index of tenderness, was increasing with time-lapse.

第二部分在&冷却牛肉贮藏期间嫩度变化的研究&中，首次探讨了牛肉在贮藏过程中嫩度变化趋势及其与pH值变化之间的相关性，以及冷却牛肉嫩度与失水率的关系。

Its advantages are: the structural design of a reasonable and practical, ingenious novel, which directly use the engine to act as cooling fan blower, on the engines to increase oxygen, and at the same time make use of cooling water tank into the engine's temperature has increased, more conducive to fuel combustion conditions, improve the thermal efficiency.

它的优点是：结构设计合理实用，构思新颖巧妙，它直接利用发动机冷却风扇充当鼓风机，对发动机进行了加氧，同时又利用了冷却水箱使进入发动机的气温有所提高，更有利于燃油燃烧的条件，提高了热效率。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。