冷却的

IR thermograph was used to perform local measurements of the surface temperature field. The results reveal that these parameters which are investigated in this paper have strong influence on the temperature gradient and the cooling efficiency.

实验结果表明：减小加温比或增大速度比都可以减小壁温梯度的绝对值，同时冷却效率也会增加；当主流进入了自模区后，随着主流速度的增加，壁温梯度的绝对值会减小，冷却效率会增大。

And the effect of steel bar type, concrete cover and cross section on the carrying capacity was analyzed.

摘要］ 进行了7根三面受火受弯试件自然冷却后承载能力的试验研究，了解了钢筋类型、混凝土保护层厚度和试件截面尺寸对自然冷却后受弯承载力的影响程度，为火灾后混凝土结构的鉴定和评估提供依据。

The CCT curve s under deformed and undeformed conditions were obtained by way of thermal dilation and metallography.

用 Gleeble-1500型热力模拟试验机研究了含钛高强度钢变形奥氏体在连续冷却过程中的相变规律，用膨胀法结合金相法建立了该钢变形和未变形奥氏体的连续冷却转变曲线，并探讨了该钢的热轧可行性。

AHT Cooling Systems GmbH is active in both branches of industrial refrigeration and deep freezing, while its main areas of business are fridges and deep freezes for supermarkets, ice cream freezers and drink cooling. The area of refrigeration and deep freezers for supermarkets basically involves plug-in refrigeration and freezer systems and constitutes approximately 62 of the total turnover.

梵高学费联盟冷却系统公司是活跃在工业制冷和速冻两个分支上的，而业务的主要领域是冰箱和超市的冰欺凌机和饮料冷却，在超市冷藏和深层冷冻面积堵塞，基本上是在制冷和冷冻系统，构成也占总营业额62。

The structure and the simulation results about the cooling, bunching ,extraction and skimming of the RFQ cooler and buncher RFQ1L,which is an important part of the being-built super-heavy nuclide research spectrometer,have been introduced.

介绍了超重核研究谱仪中RFQ冷却聚束器RFQ1L的结构和运用SIMION程序对离子的冷却、聚束、引出和撇气过程的模拟情况。

Our equipment is equipped with a water cooling system and automatic segmentation system and letoff system for choosing to use the polymer-coated with hot melt Adhesive curing time is 10-38, 15s, left, or, in a production environment normothermic cooled down the time required for this to be greater than standard time, especially in the Division of semi-finished products is cascade linescut, between the temperature so that it is difficult to give off the accumulation of natural cooling curing

我们的设备装有水冷系统和自动分割系统以及收卷系统供选择使用）覆膜用热熔胶的固化时间为10～15s左右、在生产环境常温下自然冷却所需的时间，要大于这个标准时间，特别是半成品在分割前是层叠卷绕的话。相互间温度积聚难以散发，使自然冷却固化

The coarse grain in cast strip is produced on the condition that cool speed is not fast enough to overcool aluminum melt in whole cast area, and only provide proper temprature gradiant to keep cellular grain growing up.

铸轧区内铝液与铸轧辊接触瞬间，当铸轧辊冷却强度不足以使整个断面铝液同时产生较大的过冷，而仅能保持胞状晶生长所需的液体温度梯度时，铸轧板就会出现粗大晶粒；根据传热学原理，分析了具体生产条件，提出增大铸轧辊冷却强度、降低前箱温度以及添加铝钛硼丝等防止铸轧板产生粗大晶粒的措施。

It is researched the influence of cooling rate and the content of silicon and manganese alloy on peritectic reaction and position of peritectic point in Fe-C alloy.

研究了冷却速率和硅、锰合金元素含量对Fe-C合金的包晶反应和包晶点位置的影响；由于CSP薄板坯冷却速率快，Fe-C相图向左下方移动，包晶反应区域的碳含量为0。

The properties of the combustion products have a significant effect on the heat transfer rates on the hot gas side and the properties of the coolant have a significant effect on the coolant side film coefficient.

性能燃烧的产品有重大影响的传热速率对热气体方面和性能的冷却剂有重大影响冷却剂膜侧系数。

The deodorized oils should be cooled to below 190℃ under vacuum and steam stripping.

分析油脂脱臭工艺和设备，脱臭油脂的冷却方式是影响成品油风味的关键因素，确定脱臭油应在真空和水蒸汽汽提的状态下冷却到 1 90℃以下。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。