冷却

The results show that at sea level, coolant flow rate affects the plug pressure, heat flux and temperature; at design operating condition, coolant flow rate has no effect on pressure and heat flux on the plug wall. With the same coolant flow rate, plug temperature at sea level is higher than that at design operating condition; under the same operating condition, ramp temperature is higher than the plug base temperature.

计算结果表明：地面工况下，冷却剂流量的改变对塞锥和塞锥底部壁面的压强、热流密度和温度的影响较大，高空环境下，冷却剂流量的改变对塞锥和塞锥底部壁面的压强、热流密度的影响较小；在冷却剂流量相同的情况下，塞锥和塞锥底部在地面工况下的壁面温度要远高于在高空环境下的温度；在相同工况和相同冷却剂流量的情况下，塞锥壁面上的温度要远高于塞锥底部壁面上的温度。

If the applied power is due to a initial use not the temporary power failure, the cooling temperature is set to the middle value in the cooling temperature range, and then controls loads such as a compressor and a blowing fan in the refrigerator to the driven so that the inside of the refrigerator is cooled according to the set cooling temperature.

如果是缘于首次使用而非暂时电源故障，就把冷却温度设定冷却温度范围的中间值，然后控制电冰箱的压缩机、风扇等负载，使其运转，以便冷却冰箱内部。因而，能把电冰箱的冷却温度设定到接近用户先前设定的温度控制状态。

The process and application of the cooling system of horizontal catenary continuous annealing line for stainless strip are introduced.

介绍了不锈钢带水平悬索式连续退火炉冷却系统的工艺与应用，并对某新建热轧不锈钢退火炉的冷却段进行了分析，包括初冷段、终冷段喷头的布置及影响冷却效果的因素，探讨喷水冷却系统的应用。

The cooler cavity is equipped with a double jacket containing 35-40℃ circulating oil by which the hot paste is cooled to a temperature of 70℃ and then discharged into the ACM feed hopper.

冷却机的冷却腔是双层结构，双层结构的夹套内通温度35-40℃的循环使用的冷导热油，热糊料在此冷却。待糊料冷却到70℃后，将冷糊料放置到ACM的进料料斗。

The influence of cooling conditions on the quality and metallurgical properties of sinters was studied in lab.The results show,that the heat preservation cooling is the best.

通过实验室体系研究了不同的冷却制度对烧结矿质量以及冶金性能的影响，对比分析结果表明，采用保温冷却综合效果最好，在冷却过程中采用变风量冷却对于提高烧结矿成品率有利。

This paper reports the current studies on the film cooling characteristics of single-row holes on flat plate at different blowing ratios, and analyzes the distributions of adiabatic film cooling effectiveness and heat transfer coefficient downstream the film holes.

对不同吹风比条件下的典型单排孔冷却结构的平板气膜冷却特性进行了实验研究，对冷却孔下游的气膜冷却效率及换热系数分布规律进行了分析。

For a regenerative cooling system, the coolant supply pressure must be sufficient to flow the coolant through the narrow cooling passages at high velocities.

为蓄热式冷却系统，冷却液供应的压力，必须有足够的流动冷却剂通过狭窄的通道，在冷却速度高。

As the chamber pressure increases, the only cooling methods that can satisfy the requirements are regenerative cooling only or regenerative cooling combined with film cooling.

作为商会的压力增加，只有冷却方法能够满足要求，再生冷却的唯一或再生冷却结合膜冷却。

The study shows that regenerative cooling can meet the airframe/engine integrated cooling requirements in the range of flight Mach numbers from 6 to 12, as fuel injection concept (injector locations and injection fuel mass flow) is set properly, and hydrogen temperature at the exit of cooling passage is allowed to be a relative higher value.

研究表明，在马赫数6～12的范围内，通过适当配置燃料喷射方案和提高冷却通道出口冷却剂的温度，采用再生冷却方式能够满足机体／发动机一体化高超声速飞行器的冷却需求。

When Carp vehicle fuel economy stick to the running car engine cooling system of water tanks (also called the "expansion of the pot"), after the car in a moving process, the engine heat and heat transfer to the cooling liquid, heating and cooling liquid Carp Festival Oil rods in the "Bioglass" play a role and have a lot of negative ions, with a lot of negative ion engine coolant along the cylinder piston and the cylinder head outer space waterways cycle, formed around the cylinder piston engine of the electromagnetic field.

当卡普汽车节油棒投放到汽车发动机冷却系统副水箱里后，汽车在行驶过程中，发动机发热并将热量传递给冷却液，受热的冷却液与卡普节油棒中的&Bioglass&发生作用并产生大量的负离子，充满大量负离子的冷却液沿着发动机活塞缸体和缸盖外壁的水道空间循环，形成环绕发动机活塞缸的电磁场。，发动机活塞缸中的混合燃料气体在这种电磁场作用下，形成阿萨卡瓦效应，燃烧增强、爆发力增大、燃烧效率提高，从而降低汽车燃料消耗、提高发动机动力、显著减少尾气排放。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。