冷却

The gear box of Goldwind(750kW) set is based on taking enough experience from Goldwind(600kW), takes big flux cooling lubrication system to guarantee each bearing and toothing gear can get sufficient lubrication and cooling at any working time, the filtrating system has doubt filtrating fiction, has big capacity to take dirty dust, even if the main filtre is blocked, it can supply sufficent lubricant oil by backup filtre.

润滑金风750kW机组的齿轮箱在充分吸取600kW机组经验的基础上，采取大流量润滑冷却系统以保证每个轴承和啮合轮齿都随时得到充分的润滑和冷却，过滤系统具有双重过滤功能，纳圬容量大，即使在主过滤器被堵塞情况下，油仍能通过备份滤芯向系统提供清洁足量的润滑油。

The gear box of Goldwind(750kW) set is based on taking enough experience from Goldwind(600kW), takes big flux cooling lubrication system to guarantee each bearing and toothing gear can get sufficient lubrication and cooling at any working time, the filtrating system has doubt filtrating fiction, hasbig capacity to take dirty dust, even if the main filtre is blocked, it can supply sufficent lubricant oil by backup filtre.

润滑 金风750kW机组的齿轮箱在充分吸取600kW机组经验的基础上，采取大流量润滑冷却系统以保证每个轴承和啮合轮齿都随时得到充分的润滑和冷却，过滤系统具有双重过滤功能，纳圬容量大，即使在主过滤器被堵塞情况下，油仍能通过备份滤芯向系统提供清洁足量的润滑油。

Thirdly, in order to get the high temperature sterilization method of Typha latifolia.L, the effect of intensity, time and temperature of sterilization on the color score, shear force, color difference, ascorbic acid content is measured. The optical high temperature sterilization method is to heat the raw material of Typha latifolia.L in water at 100℃ for 4min then cool fast, after vacuum package the Typha latifolia.L is sterilized at 115℃ for 15.92min and then cool entirely.

再次，为了得到蒲菜的合适高温杀菌条件，分别研究了杀菌强度、杀菌时间、杀菌温度对蒲菜的色泽感官评分、剪切力、色差、还原 Vc 含量的影响，最终得到了蒲菜的高温杀菌工艺为：将蒲菜 100℃热烫 4 分钟后快速冷却，真空包装后在 115℃杀菌 15.92 分钟后彻底冷却即成。

The properties of the combustion products have a significant effect on the heat transfer rates on the hot gas side and the properties of the coolant have a significant effect on the coolant side film coefficient.

性能燃烧的产品有重大影响的传热速率对热气体方面和性能的冷却剂有重大影响冷却剂膜侧系数。

The atomizing set takes advantage of the condensing water and external water, and atomizes them and sprays them to the surface of the condenser and refrigerator to degrade the condensing temperature and pressure, The system changes the single wind-cooling into mixed-cooling and tremendiously degrades the condensing temperature and pressure, decreases the high and low differential pressure of compressor, degrades frequent startup and operation is difficult.

空调雾化器该雾化节能装置是利用冷凝水或经过水处理后的外接水将其雾化，并将水雾喷洒到空调器或冷库冷凝器表面，使空调器或冷库单一的风冷变成风冷和雾化水冷却的混合式冷却，从而大大降低冷凝器的冷凝温度和冷凝压力，减少压缩机的高低压差，降低了压缩机由于高温保护造成跳机频繁或启动困难的现象，不仅增加了压缩机使用寿命，而且对空调器有显著的节能效果——制冷量增加，输入功率减少。

The temperature distribution in longitudinal direction, cross direction and thickness can be improved by controlling transportation speed, holding the proper proportion between upper and down water and defilading the side part separately.

通过分析生产过程中钢板纵向、横向、厚度温度分布的差异，建立了在线冷却过程中的控制冷却模型，可分别采取控制钢板输送速度、保持一定比例的上下水量及边部遮蔽的措施，改进钢板纵向、厚度及横向的温度分布。

E. thickness of the copper wire wall, length of the single conductor wire, height of the solenoid, the exciting current and the current density, the working temperature of the conductor, time of exciting and demagnetizing, the cooling water pressure and flux density, etc..

所建立的数学模型包含3个目标函数（即能耗极小化目标函数、铜耗极小化目标函数和纯铁用量极小化目标函数）、7个设计变量（即铜管规格参数a、b、t，线圈匝数N〓、N〓，铁铠磁通密度B〓和冷却水压p）和8类14个约束条件（即铜管壁厚、单饼导线长度、螺线管高度、激磁电流与电流密度、导体工作温度、激退磁时间，冷却水压和铁铠磁通密度等约束条件）。

The deodorized oils should be cooled to below 190℃ under vacuum and steam stripping.

分析油脂脱臭工艺和设备，脱臭油脂的冷却方式是影响成品油风味的关键因素，确定脱臭油应在真空和水蒸汽汽提的状态下冷却到 1 90℃以下。

The result shows that the flavors of oils and fats has a lot of differences,the cooled way of the deodorized oils is a key factor for flavor of oils and fats.

分析油脂脱臭工艺和设备，脱臭油脂的冷却方式是影响成品油风味的关键因素，确定脱臭油应在真空和水蒸汽汽提的状态下冷却到 1 90℃以下。

It use two disparting surface,and its frame is fast.It use point moulding gob,so,it can fall off automatism.When it is pulled out ,the pulling pole pull the product and accomplish the pulling of its side concave . The design project is divided into two parts. The first part is about the working theory and application of a plastic injection mould, the principle of designing and the introduction of the production about plastic mould.

它采用双分型面分型，结构紧凑；采用点浇口，且浇口可以自行脱落；顶出时，由推杆和斜顶杆顶出制品并完成制品内侧凹的抽芯；模具定模上的水道以多支回路分别冷却，动模一侧的型芯由三组水道分别冷却。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。