冷凝温度

Utilizing this simulated program, it analyzes that R11 and cooling water affect to the diathermanous performance of condenser, discusses the condenser structure depending on the working-fluid, cooling water, temperature, velocity of flow.

探讨了冷凝器结构尺寸随着工质和冷却水压力、温度、流速之间的变化关系。

Furthermore, dropwise condensation heat flux and heat transfer coefficient are increased with the higher steam saturation temperature near the atmospheric pressure.

在大气压附近，热通量和冷凝传热系数随蒸汽的饱和温度的升高而增大。

For the amorphous heat transfer surface, the dropwise condensation could be enhanced in the condition of increasing the steam pressure at a specific cooling water flow velocity.

对于非晶镀层换热表面，在特定的冷却水流量下，提高蒸汽温度可以促进珠状冷凝效果的产生。

Hygrothermal performance of building components and building elements - Internal surface temperature to avoid critical surface humidity and interstitial condensation - Calculation methods.

NF P50-766-2001 建筑元部件的湿热性能。防止临界表面潮湿和填隙式冷凝的内表面温度。

Under kylarenkommer en tank att sitta som samlar uppkondensvattnet fr n kylaren ochdet ska ocks finnas en anslutningf rstartfl kten.

在较凉，坦克坐收集冷凝水的温度，它也应该是连接以启动风扇。

Use a Fluke non-contact thermometer to read the surface temperature of uninsulated steam lines, valves and fittings

用福禄克非接触式测温仪可读取非隔热蒸汽管道、阀门和接头、收集器以及冷凝物回流管的表面温度。

The evaporating-condenser temperature reached -45℃ and the small icebox temperature reached -30℃ under the loading or free-loading circumstances in the lyophilizing box.

在冻干箱负载或空载情况下蒸发冷凝器温度均可达到- 4 5℃，小冰箱可达到- 30℃，冻干的胶原海绵具有许多孔洞的结构，冻干的菌种和去纤酶性能保持良好。

Lever Ball Float Steam Traps are not subject to the greatest advantage of pressure, temperature, condensate water flow fluctuations, continuous drainage, water that is exclusive, the Butterfly Valves minimum undercooling of 0 ℃, heating equipment can achieve the best efficiency; Lever Ball Float Steam Traps seat total in the level below, the formation of water seal, no steam leakage; its minimum working pressure 0.01Mpa, the biggest back-pressure rate of ≤ 85%; house with an exhaust device, lever float steam trap uses the most advanced components as the automatic emptying of diaphragm valves, can automatically rule out non-condensing gas, very sensitive, high-quality work and long service life.

杠杆浮球式蒸汽疏水阀的最大优点是不受压力、温度、冷凝水流量波动的影响，连续排水，有水即排，最小过冷度为0℃，能使加热设备达到最佳工作效率；杠杆浮球式蒸汽疏水阀的阀座总处于液位以下，形成水封，无蒸汽泄漏；它的最低工作压力0.01Mpa，最大背压率≤85%；内部带有排气装置，杠杆浮球式蒸汽疏水阀采用最先进的膜盒元件做为自动排空气阀，能自动排除不凝结气体，非常灵敏，工作质量高，使用寿命长。

The dependence of haze and its variation rule of low density polyethylenefilm on processing technology were discussed.

探讨了加工工艺对低密度聚乙烯薄膜雾度的影响及其变化规律，优化了加工工艺参数，确定最佳工艺条件为：熔体温度170℃，冷凝线高度20.0 cm，吹胀比3.5，牵伸比4.0；使产品透明度提高，50μm薄膜雾度在7.0％以下。

At the top of Steam-cabinet, there is a reasonable designed of the fumaroles, So when in the steam cooking process, the temperature inside of the Steam-cabinet will be kept uniformity.

蒸柜顶部有设计合理的喷汽孔，使蒸柜内的蒸汽温度在蒸煮过程中保持均匀，这样蒸柜内的冷凝水及汽既可排走，又不形成回流现象。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。