冲

When compared to other general-purpose polystyrene resins, these resins have a high flow rate, high-impact resistance and good colorability making them an excellent choice for business and consumer electronics applications that require enhanced ignition resistance versus conventional polystyrene.

与其他通用抗冲级聚苯乙烯相比，这些树脂的流动速率高，抗冲击性能高，着色力好，特别适合那些需要比一般抗冲级聚苯乙烯更高阻燃性能的商用和消费电子产品。

When I watched Se You and Liang Feng sprinted to the line, I just knew Se You's feet had been injured, not very serious, at the moment, I was compunctious, I forgot men behind us, just knew to sprint with Diu Diu and Hong Se.

当看着色友和凉风最后冲过线的时候，我才知道原来色友的脚也拧伤了，只是不重，只是那一刻我挺内疚的，自己只顾带着丢丢和乌托邦在前面冲，忘记了身后的摔国们。

The flow characteristic of undershot water is analyzed on the principle of fluid dynamics, and critical condition and theoretical calculation equation of the length of continuous flow are obtained.

根据流体动力学理论对下冲水的流动特性进行分析，得到了下冲水流保持连续性的临界条件，推导了连续流长度的理论计算公式。

Just bought an abstruse develop, try test-drive on quiet 3 annulus means in the middle of the night, he is leaving gladly, one runs quickly to exceed from the back greatly, when wanting to exceed, leave to go straight towards fellow greatly, extend a head to come, strong Xiaowang called:"Counterjumper, had left to run quickly greatly!"

导读：刚买了辆奥拓，半夜在清静的三环路上试试车，他正开得高兴，一辆大奔从后面超上来，要超过的时候，开大奔家伙，伸出头来，冲小王喊了一句："伙计，开过大奔吗！刚买了辆奥拓，半夜在清静的三环路上试试车，他正开得高兴，一辆大奔从后面超上来，要超过的时候，开大奔家伙，伸出头来，冲小王喊了一句："伙计，开过大奔吗！

This article introduces some means preventing the crackle s initiation and Stretching on the fine stamping die.

本文介绍了一些防止精冲模具裂纹产生和扩展的方法，通过这些方法可以有效提高精冲模具的寿命。

Stud shear reinforcement can be arranged in perpendicular and diametrical directions, and it should be evenly arranged around the column region.

抗冲切锚栓的布置方式包括正交布置和径向布置，且抗冲切锚栓应在柱周边区域均匀分布。

The dorsal fin is on the fish's back, which means its back is up, and its front is down toward the bottom of its pond.

背鳍在鱼的后背上，也就是说它的背是冲上面的。所以他的正面就是在下面冲着池底的。

Through analysing the structural feature and pressing technical of LJ465Q-1A petrol motor front encloser,these design emphasize introduce the pressing process planning and punch flush trim die , hole flanging moding design of petrol motor front encloser, approach how to avoid flaw , ascertain rational pressing process and dying structure ,finally in terms of pressing process drawing ,achive the punch shaving die ,hole flanging structure design and assembly drawing , major parts drawing of the part .

本设计通过对LJ465Q-1A汽油发动机前罩壳的结构特点和冲压工艺分析，着重介绍了该零件的冲压工艺过程设计及冲孔修边模、翻孔模的设计要点，探讨了避免缺陷产生的方法，确定了合理的冲压工艺过程和模具结构，并以冲压工艺过程图为依据完成了该零件冲孔切边模与翻孔模的结构设计和装配图、主要零件图的绘制。

The limit error in punching parts are the max dimension error which practicable allowed in the parts with limit error.

冲件的极限误差是具有极限偏差的冲件所具有的实际允许的最大尺寸误差。

Results show that expender cycle and fuel-rich gas generator cycle have higher synthetically specific impulse and propellant specific impulse, and have remarkably better performance than other cycles.

研究表明，膨胀循环和富燃燃气发生器循环的综合比冲和推进剂比冲较大，相对其它系统循环方案有明显的优势。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。